Gardena 4066 Betriebsanleitung - Seite 4

Blättern Sie online oder laden Sie pdf Betriebsanleitung für Rasen- und Gartengeräte Gardena 4066 herunter. Gardena 4066 9 Seiten. Electric lawn rake
Auch für Gardena 4066: Betriebsanleitung (12 seiten), Benutzerhandbuch (15 seiten), Benutzerhandbuch (15 seiten), Benutzerhandbuch (15 seiten), Benutzerhandbuch (9 seiten), Benutzerhandbuch (9 seiten)

Seite drucken
Gardena 4066 Betriebsanleitung

4. Assembly

Assemblingthehandle:
v D o not place the connecting cable
1. I nsert the two lower sections of the upright
7
with the round hole) in the mountings in the motor casing
and secure with the crosshead screws
8
3
2. I nsert the two locking bolts
in the two central sections
lower sections of the upright
4
c
2
1
3. S crew the upper part of the upright with starting handle
the central sections of the upright
bolts
1
5
This completes the assembly of the handle.
6
W arning: Fit the upper section of the upright with starting
handle
cable
8
9
(see fig.).
4. A ttach connection cable
clips
c

5. Operation

Connectingextensioncable:
1. P ush connector of extension cable
0
A
2. D raw a loop of the extension cable
relief device
T his prevents inadvertent disconnection of the plug and socket
connection.
3. I nsert extension cable
1
2
7
StartingElectric
Danger of injury if the Electric Lawn Rake does not switch
LawnRake:
off auto m atically!
v D o not remove or bridge safety devices fitted to the
E lectric Lawn Rake (e.g. by tying the starting lever to
the upper handle)!
D ANGER! The Electric Lawn Rake does not stop
immediately after the motor has been switched off:
3
C
v N ever lift, tip or carry the Electric Lawn Rake with
v N ever start on solid ground (e.g. asphalt).
v A lways maintain the safety distance between the
1. Place Electric Lawn Rake on flat grass surface.
2. K eep safety interlock
B
on the upper handle
3. Release safety interlock
14
under strain
8
during assembly.
(with the end
5
.
9
from outside through the holes
1
of the upright and secure to the
2
with two wing nuts
5
4
with two more locking
2
and the wing nuts
.
4
in such a way that the plug
with the power
3
7
is on the right side (in direction of movement)
to the handle with the two cable
8
.
on to the plug
0
through the cable strain
0
1 and suspend in position 2.
A
into a mains socket.
0
the motor running!
aerator cylinder and the user as defined by the
guide handle.
pressed down and pull starting lever
B
. The Electric Lawn Rake starts.
3
.
B
6
.
to
3

6. Maintenance

.
7
CleaningElectricLawnRake:
Adjustingforwear:
D
C
When in operation, the extension cable
0
guided in the direction you are working and to the side of the
area to be worked on.
Always work away from the connection cable.
Blockage Protection: If the aerator cylinder is blocked, e.g. by
a foreign body, immediately release the starting lever. If the
blockage lasts longer than 10 seconds and the starting lever has
not been released, blockage protection is activated. In this case
immediately release the starting lever. The Lawn Rake can be
switched on again after cooling down for approx. 1 minute.
D ANGER OF INjURY!
I f blockage protection is activated and the starting
lever is not released, the Electric Lawn Rake starts
again automatically after approx. 1 minute.
DANGER! The aerator cylinder can cause injuries!
v P rior to maintenance, unplug from the mains and
wait until the Electric Lawn Rake drum has stopped.
v Wear working gloves for performing maintenance.
The Electric Lawn Rake should be cleaned after each time it is used.
Risk of injury and physical damage!
v D o not clean Electric Lawn Rake under running
water ( particularly under high pressure).
v D o not use hard or pointed objects for cleaning
the Electric Lawn Rake.
v R emove grass and deposits from wheels, aerator cylinder and
housing.
The Electric Lawn Rake is subject to wear in use due to the way
in which it works. The more intensively the Electric Lawn Rake is
used, the greater the wear on the spring tines. Hard or very dry
ground accelerates wear as does excessive use of the Electric
Lawn Rake.
If the results of your work with the Electric Lawn Rake become
increasingly worse due to knife wear, the aerator cylinder can be
adjusted twice.
The aerator cylinder has 4 adjustment positions:
• Transport position
• Aerating position 1
• A erating position 2:
If the springs are worn (the rake roller is lowered by 3 mm).
• S etting 3:
Second setting for worn springs (the rake roller is lowered by
a further 3 mm).
Push wear compensation lever
gently away from the housing
D
and move to the position required.
must always be
15