Gardena EJ2500 Betriebsanleitung - Seite 4
Blättern Sie online oder laden Sie pdf Betriebsanleitung für Gebläse Gardena EJ2500 herunter. Gardena EJ2500 9 Seiten. Electric blower/vac
Auch für Gardena EJ2500: Betriebsanleitung (19 seiten), Betriebsanleitung (17 seiten), Benutzerhandbuch (8 seiten)
Seite drucken
Intended use:
Proper use as blower:
The GARDENA blower/vacuum is suitable when used as a blower for
sweeping debris or grass clippings from driveways, sidewalks, patios,
etc. and for blowing grass clippings, straw, or leaves into piles, or removing
debris from corners, around joints, or between bricks.
Proper use as vacuum:
The GARDENA blower/vacuum is suitable when used as a vacuum for
picking up dry material such as leaves, grass, small twigs, and bits of
paper.
DANGER! Risk of injury! If not used properly this product can be
dangerous. The warnings and safety instructions must be followed
to ensure reasonable safety and efficiency in using this product.
The operator is responsible for following the warnings and instruc-
tions in this manual and on the product. Never use the product
unless the guards provided by the manufacturer are in the correct
position.
1. SAFETY
Important! Read the operator's manual carefully before use and keep for
future reference.
Symbols on the product:
Read operator's manual.
SWITCH OFF:
Remove plug from mains before cleaning or
maintenance.
Do not expose to rain.
The use of eye and ear protection is recommended.
Keep in mind, that you probably won't hear bystanders,
which enter the working area.
Keep bystanders away.
Disconnect the mains plug if the cord
becomes damaged or entangled.
Use only with fully installed suction tube
and covered collection bag in suction mode.
Wait until the rotor blades have stopped
moving after switching off.
Do not use when wearing open hair,
loose jewellery or loose-fitting clothes.
General Power Tool Safety Warnings
WARNING: Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warning and instructions for future reference. The term "power
tool" in the warnings refers to your mains operated (corded) power tool.
1) Work area safety
a) This product is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of expe-
rience and knowledge, unless they have been given supervision or
instruction concerning the use of the product by a person responsible
for their safety. Children should be supervised to ensure that they do
not play with the product. Local regulations may restrict the age of
the operator. Never allow children or people unfamiliar with these
instructions to use the product.
Power tools are dangerous in the hands of untrained users.
b) Never operate the product while people, especially children, or pets
are nearby.
Distractions can cause you to lose control.
c) Never blow debris in the direction of bystanders. The operator or user is
responsible for accidents or hazards occurring to other people or their property.
d) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
e) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adaptor plugs with earthed (grounded) power
tools. Use only on AC mains supply voltage shown on the product rat-
ing label.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering
a power tool will increase the risk electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Before use, examine cord for damage.
Replace cord if there are signs of damage or ageing. Do not use the
product if the cord is damaged or worn. Immediately disconnect from
the mains electricity supply if the cord is cut, or the insulation is
damaged. Do not touch the electric cord until the electrical supply
has been disconnected. Do not repair a cut or damaged cord.
Replace it with a new one.
Damaged or entangled cords increase the risk of electric shock.
e) The electric cord must be uncoiled. Coiled cord can overheat and reduce
the efficiency of the product. Always wind cord carefully, avoiding kinks.
f) When operating a power tool outdoors, use an extension cord suita-
ble for outdoor use fitted with a coupler according to IEC 60320-2-3.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
g) If operating a power tool in a damp l ocation is unavoidable, use a
residual current device (RCD) protected supply with a tripping current
of not more than 30 mA. Even with a RCD installed, 100% safety
cannot be guaranteed and safe working practices must be followed
at all times. Check your RCD every time you use your product.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always wear eye protection and
hearing protection. To prevent dust irritation, the use of a dust mask
is recommended.
Protective equipment such as eye protection, hearing protection, dust mask,
nonskid safety shoes, or hard hat used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position
before connecting to power source, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools
that have the switch on invites accidents.
d) Do not overreach. Keep proper footing and balance at all times.
On slopes, be extra careful and wear non-slip footwear. Do not walk
backwards while operating your product. Walk, never run. Do not use
ladders while operating the product.
This enables better control of the power tool in unexpected situations.
e) Dress properly. Always wear suitable clothing, gloves, and stout shoes.
Do not wear loose clothing or jewellery. Keep your hair, clothing and
gloves away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
4) Power tool use and care
a) Only use the product in the manner and for the functions described in
these instructions. Always direct the cord to the rear, away from the
product. Do not force the power tool. Use the correct power tool for
your application. The correct power tool will do the job better and safer at
the rate for which it was designed.
b) Always make sure your product is in a safe operating condition before
use. Do not use the power tool if the switch does not turn it on and
off. Know how to stop the product quickly in an emergency.
Any power tool that cannot be controlled with the switch is dangerous and
must be repaired.
c) The impeller continues to rotate after your product has been switched
off. The motor must be stopped and the impeller blade no longer turning to
avoid serious injury from the rotating blades.
d) Disconnect the plug from the power source:
– before removing or replacing fully assembled debris bag;
– before leaving the product unattended for any period;
– before clearing a blockage;
17