Garmin RV-IN1501 Benutzerhandbuch - Seite 26

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Auto-Navigationssystem Garmin RV-IN1501 herunter. Garmin RV-IN1501 36 Seiten. Rv infotainment system
Auch für Garmin RV-IN1501: Einbauanleitung (4 seiten)

Seite drucken

Select Fusion Media >

DHCP SERVER > DHCP ENABLED > SAVE.

You can configure the IP address range of the DHCP server

(DHCP Settings, page

20).

Setting the FUSION PartyBus Device as a Wireless Access

Point

Before you can connect additional FUSION PartyBus devices or

smartphones to a FUSION PartyBus device wirelessly, you must

configure at least one device as a wireless access point. This is

not necessary if you installed a wireless router or other wireless

access point on the network.

Select Fusion Media >

POINT.

Select SSID, and change the default SSID, or name, for the

wireless access point (optional).

Select AP SECURITY, and change the security type for the

access point (optional).

NOTE: It is strongly recommended that you use the default

WPA2 PERSONAL AP SECURITY setting. It is the most

widely-used and secure wireless security protocol.

Select PASSWORD, and change the default password for

the access point (optional).

If necessary, select COUNTRY, and select your region.

Select CHANNEL, and select a channel range for the access

point (optional).

Select SAVE.

You can adjust the wireless access point configuration at any

time

(Wireless Access Point Settings, page

Connecting the FUSION PartyBus Device to a Wireless

Access Point

Select Fusion Media >

SSID.

A list of wireless access points within rage appears.

Select the FUSION PartyBus wireless access point.

Select an option:

• To enter the password, select PASSWORD, enter the

password, and select

• If you are connecting to the wireless access point using

WPS, verify that WPS has been enabled on the access

point, and select WPS.

NOTE: It can take up to two minutes to successfully

connect to the access point after you select WPS.

Select SAVE.

Advanced Network Configuration

You can perform advanced networking tasks on a FUSION

PartyBus device, such as defining DHCP ranges and setting

static IP addresses.

Wireless Access Point Settings

Select Fusion Media >

ACCESS POINT.

NOTE: You must configure the device to be a wireless access

point before you can change the settings

PartyBus Device as a Wireless Access Point, page

SSID: Sets the SSID, or name, for the network.

AP SECURITY: Sets the type of wireless security protocol used

by the access point.

NOTE: It is strongly recommended that you set the AP

SECURITY using WPA2 PERSONAL. It is the most widely-

used and secure wireless security protocol.

PASSWORD: Sets the password for the access point. This is

not available when the AP SECURITY setting is set to

NONE.

> NETWORK > ADVANCED >

> NETWORK > WI-FI ACCESS

20).

> NETWORK > WI-FI CLIENT >

> NETWORK > ADVANCED > WI-FI

(Setting the FUSION

20).

COUNTRY: Sets the region where the stereo is located.

Different regions may use different channels on the wireless

spectrum, so you should set this to best accommodate local

wireless devices.

CHANNEL: Sets the access point to use a group of channels in

the high, low, or middle range of the available spectrum for

your region. You may experience better performance if you

set the channel in a range with fewer broadcasting access

points.

DHCP SERVER: Sets the device to act as a wireless access

point and the DHCP server on the network

page

20).

WPS: Initiates a Wi‑Fi Protected Setup (WPS) connection.

Devices with a WPS button or setting can connect to the

access point on this stereo when the WPS connection is

active.

NOTE: It can take up to two minutes to successfully connect

to the access point after you select WPS.

DHCP Settings

Select Fusion Media >

SERVER.

DHCP ENABLED: Sets the device as the DHCP server on the

network.

START IP: Sets the first IP address in the IP-address range of

the DHCP server.

END IP: Sets the final IP address in the IP-address range of the

DHCP server.

Setting a Static IP Address

If the stereo is configured as a DHCP server, it is automatically

assigned the IP address of 192.168.0.1. You can change this IP

address.

If the stereo is a client on the network and you do not want the

DHCP server to automatically assign an IP address to the

stereo, you can set a static IP address.

NOTE: Every device on the network must have a unique IP

address. If you select a static IP address that is the same as the

IP address on the network, the devices will not work properly.

Select Fusion Media >

FI IP > STATIC IP.

Select an option:

• To set the IP address, select IP, and enter the IP address.

• To set the subnet mask, select MASK, and enter the

subnet mask.

NOTE: The subnet mask must match all other devices on

the network to work properly. A typical subnet mask is

255.255.255.0.

• To set the default gateway IP address, select GATEWAY,

and enter the gateway IP address.

NOTE: The default gateway is typically set as the IP

address of the DHCP server on the network.

Select Save.

Resetting Network Settings

You can reset all network settings for this stereo to the factory

default values.

Select Fusion Media >

Additional Stereo Control Options

FUSION-Link Wireless Remote Control App

You can use the FUSION-Link remote control app on your

compatible Apple or Android device to adjust the stereo volume,

change the source, control playback, select and manage radio

presets, and adjust some stereo settings.

The app communicates with the stereo using a wireless

connection to the mobile device. You must connect your

(DHCP Settings,

> NETWORK > ADVANCED > DHCP

> NETWORK > ADVANCED > WI-

> NETWORK > RESET > YES.

Media Playback