Brother 888-N20 Betriebshandbuch - Seite 30
Blättern Sie online oder laden Sie pdf Betriebshandbuch für Nähmaschine Brother 888-N20 herunter. Brother 888-N20 32 Seiten.
Auch für Brother 888-N20: Betriebshandbuch (32 seiten)
Seite drucken
Symptom, Cause/solution
The sewing light bulb does not come on�
The sewing light is damaged�
The fabric feeds in the opposite direction�
The feed mechanism is damaged�
The needle contacts the needle plate�
The needle clamp screw is loose�
The needle is turned, bent or the point is dull�
Fabric being sewn with the machine cannot be
removed�
Thread is tangled below the needle plate�
A broken needle has fallen into the machine�
X
Turn off the machine, and remove the needle
plate� If the needle that fell into the machine
can be seen, use tweezers to remove it�
After removing the needle, return the needle
plate to its original position and insert a
new needle� Before turning on the machine,
slowly turn the handwheel toward you to
check that it turns smoothly and that the
new needle enters through the center of the
needle plate opening� If the handwheel does
not turn smoothly or the needle that fell into
the machine cannot be removed, consult
your authorized Brother dealer or the nearest
Brother authorized service center�
The handwheel does not turn smoothly�
Thread is tangled in the bobbin case�
Decorative stitch patterns are misaligned�
A wrong presser foot is used�
Stitch adjustment is set incorrectly�
Error Messages
No�
Cause
The foot controller was
pressed (or
button) was pressed if the foot
controller is not connected ★)
or
(Reverse/Reinforcement
stitch button) was pressed
while the presser foot is
raised�
A stitch other than the
buttonhole or bar tack stitch
was selected and the foot
controller was pressed (or
"Start/Stop" button) was
(
pressed if the foot controller
is not connected ★) while the
buttonhole lever is lowered�
The buttonhole or bar tack
stitch was selected and the
foot controller was pressed (or
"Start/Stop" button) was
(
pressed if the foot controller
is not connected ★) while the
buttonhole lever is raised�
30
★
Solution
"Start/Stop"
(
Lower the presser
foot lever before
continuing the
operation�
Raise the
buttonhole
lever before
continuing the
operation�
Lower the
buttonhole
lever before
continuing the
operation�
Reference
No�
Cause
stitch button) (or
*
position button) ★) was
pressed while the bobbin
winder shaft is moved to the
*
right�
13
was pressed while the foot
13
controller is connected�
The motor locked up because
27
the thread is tangled�
The stitch only for the single
needle was selected and the
foot controller was pressed (or
pressed if the foot controller
is not connected
24
twin needle mode is active�
The machine may be
malfunctioning�
Operation beep ★
27
• When the machine is turned on or a key is pressed
(correct operation)
14
One beep
X
23
• When the machine is turned on while a setting is
changed (page 6)
X
Two beeps
• If an incorrect operation is performed or a non-
functioning key is pressed
Two or four beeps
X
• If the machine locks up, for example, because the
thread is tangled
Beeps for four seconds and the machine
X
automatically stops�
Be sure to check for the cause of the error, and
correct it before continuing to sew�
(Reverse/Reinforcement
(Needle
"Start/Stop" button)
(
★
"Start/Stop" button) was
(
) while the
★
★
: Only for some models�
Solution
Move the bobbin
winder shaft to
the left before
continuing the
operation�
Disconnect the
foot controller
or use the foot
controller�
★
Remove
the tangled
thread before
continuing the
operation�
Select a stitch for
the twin needle�
Contact your
nearest Brother
authorized
service center�