Garmin Cessna Caravan G1000 Handbuch für Piloten - Seite 8

Blättern Sie online oder laden Sie pdf Handbuch für Piloten für Avionik-Display Garmin Cessna Caravan G1000 herunter. Garmin Cessna Caravan G1000 16 Seiten. Integrated flight deck
Auch für Garmin Cessna Caravan G1000: Handbuch für Piloten (6 seiten), Handbuch für Piloten (32 seiten), Handbuch für Piloten (25 seiten), Handbuch für Piloten (34 seiten), Handbuch für Piloten (21 seiten), Ergänzung zum Flughandbuch für Flugzeuge (33 seiten), Handbuch für Piloten (22 seiten)

GIA 63

The GIA 63 units serve as the main interface hub for the individual components of the G1000 system. All key components, such as

the GRS 77 AHRS, GDC 74A ADC, GTX 33 Mode-S transponder and GEA 71 Engine/Airframe Interface, provide inputs to both GIA 63

units. This allows for a higher level of system redundancy and integrity as data is cross-checked to ensure proper system operation.

The only component that is not connected directly to the GIA 63 units is the GMU 44 magnetometer; the latter interfaces directly with

the GRS 77 AHRS to provide it with magnetic heading input. The GIA 63 units also contain the communication and navigation radios

that include the VOR/LOC/GS and GPS receivers.

Failure Mode(s)

If a GIA 63 unit fails, the associated COM/NAV/GPS receiver data is no longer available and is automatically replaced by the COM/

NAV/GPS receiver data from the other GIA 63 unit. The operative GPS receiver automatically takes over any active GPS navigation

(without any pilot input). A red "X" appears over the COM/NAV frequencies to indicate GIA 63 failure (see Figure 4) and an alert

annunciation appears to the right of the altitude/vertical speed tapes on the PFD. The remaining GIA 63 continues to provide all

interface and system integrity functions. If both GIA 63 units fail, the AHRS and ADC continue to provide data directly to the GDU

units, although no navigational or communication capabilities are available. Partial failures in the GIA 63 units (such as failure of the

COM component) are more likely to occur than full component failures since the COM/NAV/GPS and interface components are all

independent inside the GIA 63.

The GDC 74A is the ADC for the system and receives the standard pitot and static system inputs as well as the outside air tempera-

ture (OAT) input. This allows the system to automatically perform most E6B calculations, such as that of density altitude and true

airspeed.

Failure Mode(s)

If the GDC 74A fails, the PFD presentations of the airspeed, altitude, vertical speed, OAT and true airspeed (TAS) display a red "X",

as shown in Figure 4. In this case, the pilot should refer to the standby altitude and airspeed indicators installed in the aircraft. Certain

obstructions of the pitot static system can be veriﬁed by cross-checking the associated PFD indications with the standby instruments.

These PFD indications should be consistent with the readings found in non-G1000-equipped aircraft (zero airspeed on takeoff, etc.).

If the OAT probe fails, a red "X" appears both on the TAS box and the OAT box, and E6B-type calculations should be completed manu-

ally. Pressure altitude reporting for the transponder is also lost. That is, the transponder can only work in Mode A and can no longer

provide the information necessary for operating in Class C and B airspace.

The GRS 77 AHRS provides attitude and turn-rate presentation on the PFD and is interfaced with the GMU 44 magnetometer. The

GMU 44 is a tri-axial magnetometer which allows the system to measure both the horizontal and vertical components of the earth' s

magnetic ﬁeld. Both the GRS 77 and GMU 44 are solid-state components that require very little initialization time (less than one

minute) and that can initialize while moving during taxi and in ﬂight at bank angles of up to 20 degrees. The GRS 77 AHRS can still

operate in the absence of other reference inputs such as those from the GPS receiver, ADC, or magnetometer.

Failure Mode(s)

If the system detects that the GRS 77 is not operating properly when compared to other aircraft sensors, such as the GPS receiver,

ADC, or magnetometer, all attitude presentations are removed from the PFD and are replaced with a large, red "X" and the words "At-

titude Fail" (see Figure 4). Failure indications are designed to be displayed before any hazardous or misleading information (HMI) is

presented to the pilot. This represents a signiﬁcant improvement over conventional mechanical gyro systems. If the GMU 44 fails,

only the stabilized heading data is lost.

G1000 SYSTEM COMPONENTS

Garmin G1000 Guide for Designated Pilot Examiners & Certiﬁed Flight Instructors

190-00368-02 Rev. A