Garmin Echomap Plus 40 series Installationsanweisung - Seite 2
Blättern Sie online oder laden Sie pdf Installationsanweisung für GPS-System für die Schifffahrt Garmin Echomap Plus 40 series herunter. Garmin Echomap Plus 40 series 6 Seiten.
Auch für Garmin Echomap Plus 40 series: Benutzerhandbuch (50 seiten), Installationsanleitung Handbuch (6 seiten)
Seite drucken
2
Place the swivel mount on the base, and replace the 10 mm
M6×1 Phillips screw.
3
Seal the cable pass-through holes with marine sealant.
Preparing to Run Cables under the Mounting Surface
Use pan-head screws or bolts when securing the swivel-mount
base. Screws or bolts with countersunk heads damage the
base.
Before you can prepare the swivel-mount base, you must
choose the location to install the mount and decide whether to
attach the mount using screws or bolts.
1
Remove the 10 mm M6x1 Phillips screw
swivel mount
from the base
2
Orient the swivel base so the pass-through holes
desired direction.
3
Using the swivel base as a template, mark the pilot hole
locations
.
4
Mark the cable routing hole
5
Using the appropriate drill bit for the hardware, drill the three
pilot holes.
6
5
Using a 16 mm (
/
in.) drill bit, drill the cable-routing hole.
8
2
NOTICE
and separate the
.
.
Fastening the Swivel Mount with the Cables Running
through the Mount
You should complete this procedure only when running the
power and transducer cables under the mounting surface and
through the swivel-mount base.
1
Feed the cables through the 16 mm (
drilled when preparing to run cables beneath the mounting
surface.
2
Place the base on the mounting surface.
3
Route the cables through the cable pass-through holes.
4
Loosely fasten the base using the appropriate screws or
bolts.
5
Place the swivel mount on the base, but do not fasten it.
6
Place the cradle or device into the swivel mount
the Device in the Cradle, page
7
Pull out enough slack from the power and transducer cables
so the mount can fully swivel to the desired positions when
the cables are connected.
8
Remove the cradle and the swivel mount from the base.
9
Apply marine sealant to the 16 mm (
the cable pass-through holes.
10
Securely fasten the base with the appropriate screws or
bolts.
11
Place the swivel mount on the base, and fasten it using the
included 10 mm M6×1 Phillips screw.
Installing the Cradle in the Mount
1
Pull up the locking arm
face the
2
Place the cradle into the swivel mount
3
Tilt the mount to the desired viewing angle.
4
Press down the locking arm.
Installing the Cables and Connectors
Wiring to Power
1
Route the power cable from the mount to the boat battery or
fuse block.
2
If necessary, extend the wires using 0.82 mm
larger wire.
3
Connect the red wire to the positive terminal on the battery or
fuse block, and connect the black wire to the negative
terminal.
Wiring Harness
• The wiring harness is used for NMEA
share route and waypoint information.
• The wiring harness connects the device to power and NMEA
0183 devices.
• The device has one internal NMEA 0183 port that is used to
connect to NMEA 0183 compliant devices.
• If it is necessary to extend the power and ground wires, you
must use 0.82 mm
5
/
in.) center hole you
8
4).
5
/
in.) center hole and to
8
.
.
0183 devices, and to
®
2
(18 AWG) or larger wire.
(Installing
2
(18 AWG) or