Garmin GPSMAP 9X2 PLUS Installationsanleitung Handbuch

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für GPS-System für die Schifffahrt Garmin GPSMAP 9X2 PLUS herunter. Garmin GPSMAP 9X2 PLUS 8 Seiten.

Seite drucken

GPSMAP

INSTALLATION

INSTRUCTIONS

Important Safety Information

Failure to follow these warnings, cautions, and notices could

result in personal injury, damage to the vessel or device, or poor

product performance.

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place voids the product warranty.

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

To avoid possible personal injury or damage to the device and

vessel, disconnect the vessel's power supply before beginning

to install the device.

To avoid possible personal injury or damage to the device or

vessel, before applying power to the device, make sure that it

has been properly grounded, following the instructions in the

guide.

For the best possible performance, the device must be installed

according to these instructions.

When drilling or cutting, always check what is on the opposite

side of the surface to avoid damaging the vessel.

Read all installation instructions before proceeding with the

installation. If you experience difficulty during the installation,

contact Garmin

Product Support.

Contacting Garmin Support

• Go to

support.garmin.com

product manuals, frequently asked questions, videos, and

customer support.

• In the USA, call 913-397-8200 or 1-800-800-1020.

• In the UK, call 0808 238 0000.

• In Europe, call +44 (0) 870 850 1241.

November 2020

7X2/9X2 PLUS

WARNING

CAUTION

NOTICE

for help and information, such as

Software Update

You may need to update the chartplotter software after

installation. For the instructions on how to update the software,

see the owner's manual at

-9x2Plus.

Tools Needed

• Drill

• Drill bits appropriate for the device and mounting style

Mounting Style

Bail with included M4 wood screws

Flush

Flush with included M3.5 wood screws (702 series) 2 mm (

Flush with included M4 wood screws (902 series)

Flush with included machine screws and nut plates 6 mm (

Flush with included M3.5 machine screws and

tapped holes (702 series)

Flush with included M4 machine screws and tapped

holes (902 series)

• #2 Phillips screwdriver

• Jigsaw or rotary tool

• File and sandpaper

• Marine sealant (recommended)

Mounting Considerations

This device should be mounted in a location that is not exposed

to extreme temperatures or conditions. The temperature range

for this device is listed in the product specifications. Extended

exposure to temperatures exceeding the specified temperature

range, in storage or operating conditions, may cause device

failure. Extreme-temperature-induced damage and related

consequences are not covered by the warranty.

When selecting a mounting location, you should observe these

considerations.

• The location should provide optimal viewing as you operate

your boat.

• The location should allow for easy access to all device

interfaces, such as the keypad, touchscreen, and card

reader, if applicable.

• The location must be strong enough to support the weight of

the device and protect it from excessive vibration or shock.

• To avoid interference with a magnetic compass, the device

should not be installed closer to a compass than the

compass-safe distance value listed in the product

specifications.

• The location must allow room for the routing and connection

of all cables.

• The location must not be a flat, horizontal surface. The

location should be in a vertical angle.

The location and viewing angle should be tested before you

install the device. High viewing angles from above and below

the display may result in a poor image.

Bail Mounting the Device

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

GUID-58383C42-BCE0-4965-BFF1-A648A7E884FC v2

garmin.com/manuals/GPSMAP7x2

Drill Bit Sizes

3.2 mm (

13 mm (

3.2 mm (

4 mm (

M3.5 tap

M4 tap

NOTICE

in.)