Garmin GNX Installationsanleitung Handbuch - Seite 2

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Schiffsausrüstung Garmin GNX herunter. Garmin GNX 28 Seiten. Mast bracket
Auch für Garmin GNX: Installationsanweisung (48 seiten)

Seite drucken

GNX

™

Keypad Installation Instructions

Important Safety Information

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

When drilling or cutting, always check what is on the opposite

side of the surface.

Registering Your Device

Help us better support you by completing our online registration

today.

• Go to http://my.garmin.com.

• Keep the original sales receipt, or a photocopy, in a safe

place.

Contacting Garmin

Product Support

• Go to

http://www.garmin.com/support

information.

• In the USA, call 913-397-8200 or 1-800-800-1020.

• In the UK, call 0808 238 0000.

• In Europe, call +44 (0) 870 850 1241.

Tools Needed

• Drill and drill bits

◦ 44 mm (1

in.) hole saw

◦ 2.8 mm (

in.) drill bit

• Marine sealant (recommended)

Installing the Device

Mounting Considerations

This device should be mounted in a location that is not exposed

to extreme temperatures or conditions. The temperature range

for this device is listed in the product specifications. Extended

exposure to temperatures exceeding the specified temperature

range, in storage or operating conditions, may cause device

failure. Extreme-temperature-induced damage and related

consequences are not covered by the warranty.

This device can be mounted in dashboard or other surface using

the included hardware. When selecting a mounting location,

observe these considerations.

• To avoid interference with a magnetic compass, the device

should not be installed closer to a compass than the

compass-safe distance value listed in the product

specifications.

• The location must allow room for the routing and connection

of the cables.

Mounting the Device

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid any cracking in the gel-coat layer when the screws are

tightened.

WARNING

CAUTION

NOTICE

for in-country support

NOTICE

The included template and hardware can be used to mount the

device at the selected location.

Trim the flush-mount template and make sure it fits in the

location where you want to mount the device.

Secure the template to the selected location.

Using 44 mm (1

in.) hole saw or rotary cutting tool, cut the

mounting surface along the inside of the solid line on the

template.

Place the device

in the cutout and make sure the mounting

holes on the device line up with the pilot holes

template.

If the mounting holes on the device do not line up, mark the

new pilot-hole locations.

Using either a 2.8 mm (

appropriate for the mounting surface, drill the pilot holes.

Remove the template from the mounting surface.

If you will not have access to the back of the device after you

mount it, connect all necessary cables to the device before

placing it into the cutout.

Place the device into the cutout.

Secure the device to the mounting surface using the included

screws

Install the decorative bezel by snapping it in place around the

edges of the device.

NMEA 2000

Connection Considerations

If you have an existing NMEA 2000 network on your boat, it

should already be connected to power. Do not connect the

NMEA 2000 power cable to an existing NMEA 2000 network,

because only one power source should be connected to a

NMEA 2000 network.

If you are installing a NMEA 2000 power cable, you must

connect it to the boat ignition switch or through another in-line

switch. NMEA 2000 devices will drain your battery if the NMEA

2000 power cable is connected to the battery directly.

The keypad connects to a NMEA 2000 network on your boat.

The NMEA 2000 network provides power to the keypad and

allows you to control compatible marine instruments connected

to the same NMEA 2000 network. The included NMEA 2000

cable and connectors allow you to connect the keypad to your

existing NMEA 2000 network.

If you are unfamiliar with NMEA 2000, you should read the

"NMEA 2000 Network Fundamentals" chapter of the Technical

Reference for NMEA 2000 Products. To download the

reference, go to www.garmin.com/manuals/GNX120.

on the

in.) drill bit, or a drill bit

NOTICE