Garmin GPSMAP 8700 Installationsanleitung Handbuch - Seite 4
Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Schiffsausrüstung Garmin GPSMAP 8700 herunter. Garmin GPSMAP 8700 6 Seiten.
Auch für Garmin GPSMAP 8700: Installationsanleitung Handbuch (27 seiten), Installationsanleitung Handbuch (8 seiten)
Seite drucken
Item
Description
12 Vdc power source
NMEA 2000 terminator or backbone cable
NMEA 2000 T-connector
NMEA 2000 terminator or backbone cable
J1939 Engine Network Connection Considerations
You must use a Garmin GPSMAP J1939 accessory cable when
connecting the chartplotter to the J1939 engine network to
prevent corrosion due to moisture. Using a different cable voids
your warranty.
If you have an existing engine network on your boat, it should
already be connected to power. Do not add any additional power
supply.
This chartplotter can connect to an engine network on your boat
to read data from compatible devices such as certain engines.
The engine network follows a standard and uses proprietary
messages.
You should connect only one chartplotter to one engine network.
Connecting more than one chartplotter to one engine network
may result in unexpected behavior.
The port labeled J1939 is used to connect the device to the
existing engine network. You must route the cable within 6 m
(20 ft.) of the engine network backbone.
The Garmin GPSMAP J1939 accessory cable requires
connection to a power source and proper termination. For more
information on connecting to your engine network, see the
manufacturer's engine documentation.
Pin
Wire Color
Bare
Red
Black
White
Blue
HDMI Video Considerations
To prevent corrosion due to moisture, you must use Garmin
GPSMAP accessory cables when connecting the chartplotter to
the video source or display. Do not connect a media player stick
directly into the back of the chartplotter. Using different cables or
connecting a media player stick into the back of the chartplotter
voids your warranty.
The GPSMAP 8700 chartplotter allows video input from HDMI
video sources, such as a Chromecast
protected HDMI content (HDCP content), though. Check the
video source's manual to verify that HDCP can be turned off for
the source.
HDMI video is shared across the Garmin Marine Network, but it
is not shared across the NMEA 2000 network.
Through the HDMI OUT port, you can display the video on
screen, such as a television or monitor.
The Garmin GPSMAP HDMI accessory cable is 4.5 m (15 ft)
long. If you need a longer cable, you should use an active HDMI
4
NOTICE
Description
Shield
Power, positive
Power, negative
CAN High
CAN Low
NOTICE
™
device. You cannot view
cable only. You need an HDMI coupler to connect the two HDMI
cables.
You need a Garmin GPSMAP USB OTG adapter cable to power
a media player stick. The USB HOST port can supply up to
2.5 W to power a media player stick.
You must make all cable connections in a dry environment.
Item Device or port
HDMI source, such as a
Chromecast device
GPSMAP chartplotter
Monitor, such as a computer or
television
HDMI source's HDMI OUT port
Chartplotter's HDMI IN port
Chartplotter's HDMI OUT port
Monitor's HDMI IN port
Chartplotter's USB OTG or USB
HOST port
HDMI source's USB HOST port
Composite Video Considerations
This chartplotter allows video input from composite video
sources using the port labeled CVBS IN. When connecting
composite video, you should observe these considerations.
• The CVBS IN port uses a BNC connector. You can use a
BNC to RCA adapter to connect a composite-video source
with RCA connectors to the CVBS IN port.
• Video is shared across the Garmin Marine Network, but it is
not shared across the NMEA 2000 network.
Touchscreen Controls for a Connected Computer
To prevent corrosion due to moisture, you must use Garmin
GPSMAP accessory cables when connecting the chartplotter to
the computer. Using different cables voids your warranty.
You can connect the chartplotter to a computer to see the
computer screen and to control the computer using a
touchscreen. To see the computer screen, you must connect the
computer to the HDMI IN port and connect the touchscreen to
the HDMI OUT port. To control the computer using the
chartplotter touchscreen, you must connect the computer to the
USB OTG port and connect the touchscreen to the USB HOST
port.
The HDMI Cable (010-12390-20) is 4.5 m (15 ft) long. If you
need a longer cable, you should use an active HDMI cable only.
You need an HDMI coupler to connect the two HDMI cables.
The Garmin OTG Adapter Cable (010-12390-11) is 1.8 m (6 ft)
long and the Garmin USB Cable (010-12390-10) is 4.5 m (15 ft)
long. If you need a longer cable, you should use a USB hub or
USB repeater extension cable only.
You must make all cable connections in a dry environment.
Cable
Garmin HDMI Cable
Garmin HDMI Cable
GPSMAP USB OTG adapter
cable to power the HDMI
source, if possible (2.5 W
maximum)
NOTICE