Garmin Delta Upland Benutzerhandbuch - Seite 6
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Haustierpflegeprodukt Garmin Delta Upland herunter. Garmin Delta Upland 14 Seiten. Instructions
Auch für Garmin Delta Upland: Anweisungen (4 seiten)
![Garmin Delta Upland Benutzerhandbuch](/uploads/products/server2/2333189/2333189.jpg)
You should fully charge the battery before you use the device
for the first time. Charging a fully depleted battery takes about
two hours. The device will not charge when outside the
temperature range of 32° to 104°F (0° to 40°C).
1
Snap the charging clip
2
Plug the small end of the power cable into the mini-USB port
on the charging clip.
3
Plug the other end of the power cable into a power source.
The status LED is solid red when the collar is charging.
4
After the status LED turns solid green, remove the charging
clip from the collar.
Attaching the Devices to the Collar Strap
1
With the buckle
facing outward, insert the end of the collar
strap through the slot
2
Pull approximately two-thirds of the collar strap through the
slot.
3
Insert the end of the collar strap through the slot
opposite side of the device.
4
Pull the strap until it is tight across the front of the device.
5
Insert the end of the collar strap through the slot
Beeper device.
2
onto the device.
on the collar device.
Turning On the Devices
• On the handheld device, hold the power key until the
LCD display turns on.
• On the dog collar device, hold the power key until the status
LED flashes and the collar beeps.
• On the beeper device, hold the power key until the red status
LED flashes once.
Turning Off the Devices
• On the handheld device, hold the power key until the
LCD display turns off.
• On the dog collar device, hold the power key until the status
LED flashes and the collar beeps once.
• On the beeper device, hold the power key until red status
LED turns off, and then release the power key immediately.
Dog Collar Devices
You can use up to three dog collar devices with a single
handheld device. You can select a different training mode and
intensity level for each dog collar device.
Each dog collar device must be paired with the handheld device
before it can be used. During the pairing process, each dog
collar device is associated with a color on the handheld device.
indicates the selected color.
Pairing a Dog Collar Device with the Handheld Device
NOTE: If your handheld device and dog collar device were
included in the same package, the devices are paired from the
factory using the black color selection.
1
Turn on the dog collar device and the handheld device.
2
On the handheld device, select
indicates the selected color.
3
On the handheld device, select an intensity level greater than
0
(Changing the Intensity
4
On the dog collar device, hold the power key for about two
seconds.
The device beeps once when you press the button and again
after two seconds.
5
After the second beep, on the handheld device, select a
training key.
The dog collar device turns off and beeps to indicate whether
the devices paired successfully.
Short beep
Long beep
TIP: If the devices did not pair successfully, you should verify
the batteries in both devices are fully charged and the intensity
level is set higher than 0.
on the
Selecting a Dog Collar Device
Before you can select and control a dog collar device, you must
pair the dog collar device with the handheld device
on the
Dog Collar Device with the Handheld
Select
to choose the color.
indicates the selected color.
The training keys control the dog collar device associated with
the selected color.
The beeper device emits high-volume sounds to provide
information about the location and status of your dogs. You can
operate the beeper device remotely using the Delta Upland
system.
to choose the color.
Level).
Devices paired successfully
Devices did not pair
Device).
Beeper Device
(Pairing a
Beeper Device