Fujitsu 9333003030-02 Betriebshandbuch - Seite 4

Blättern Sie online oder laden Sie pdf Betriebshandbuch für Klimagerät Fujitsu 9333003030-02 herunter. Fujitsu 9333003030-02 9 Seiten. Wall mounted type

Seite drucken

Remote Controller Overview and Operations

Remote controller display

In this section, all the possible indicators are displayed for description.

In actual operation, the display is linked with the button operation, and

only shows the necessary indicators for each setting.

POWERFUL button

Activates the POWERFUL operation.

The unit will operate at maximum power and strong airflow to quickly

cool down or warm up the room.

When activated, the indoor unit will emit 3 short beeps.

POWERFUL operation is automatically turned off in the following

situations:

• Adjusted room temperature reaches the set temperature in COOL,

DRY, or HEAT mode.

• 20 minutes have passed after the POWERFUL operation mode has

been set.

Even in situations above, the POWERFUL operation will not

automatically turn off unless it has run for a certain amount of time.

Notes:

• The airflow direction and the fan speed are controlled automatically.

• This operation cannot be performed simultaneously with ECONOMY

operation.

To return to normal operation, press the button again. Then the indoor

unit will emit 2 short beeps.

10 °C HEAT button

Starts 10 °C HEAT operation that maintains the room temperature at

10 °C so as to prevent the room temperature to drop too low.

After pressing the button to start the 10 °C HEAT operation, the

indoor unit emits 2 short beeps and the ECONOMY indicator (green)

will turn on.

Notes:

• In 10 °C HEAT operation mode, only vertical airflow direction can be

adjusted by using

• HEAT mode will not be performed if the room temperature is warm enough.

• In multi-type air conditioning system, if other indoor unit is in HEAT

mode, the temperature of the room where 10 °C HEAT operation is

performed will rise. When performing 10 °C HEAT operation, all the

indoor units should be run in 10 °C HEAT operation mode.

To turn off, press the START/STOP button.

The ECONOMY indicator will turn off.

Signal transmitter

Aim to signal receiver of the indoor unit properly.

• Signal transmit indicator

that signal from the remote controller is being transmitted.

• Operating range is approximately 7 m.

• You will hear a beep if the transmitted signal has been sent properly.

If there is no beep, press the button on the remote controller again.

FAN button

Controls the fan speed.

(AUTO)

(HIGH)

• When AUTO is selected, the fan speed is automatically adjusted

according to the operation mode.

SWING button

Starts or stops automatic swing of the vertical airflow direction louver.

• Each time you press the button, the vertical airflow direction louver

swings as follows:

COOL, DRY, or FAN

6 7

Notes:

• SWING operation may stop temporarily when the indoor unit fan is

rotating at very low speed or is stopped.

• In FAN mode, swing operation range of 1 ↔ 3 or 4 ↔ 7 is decided

according to the airflow direction previously set before starting the

swing operation.

En-4

OPERATING MANUAL

button.

on the remote controller display shows

(MED)

(LOW)

(QUIET)

HEAT or FAN mode

mode

10 SET button

Adjusts the vertical airflow direction.

11 SLEEP timer button

Activates the SLEEP timer that helps you to fall asleep comfortably

with gradual temperature control.

12 Timer CANCEL button

Cancels the set timer.

13 RESET button

When you press the RESET button, press it gently by using the tip of a

ballpoint pen or other small object in correct direction as shown in this figure.

RESET

14 CLOCK ADJUST button

Used for adjusting the clock.

15 OFF timer button

Activates the OFF timer.

16 ON timer button

Activates the ON timer.

17 SELECT button

Used for adjusting the clock or timer.

18 OUTDOOR UNIT LOW NOISE button

Starts or stops OUTDOOR UNIT LOW NOISE operation that lowers

noise generated from the outdoor unit by cutting down the rotation

number of the compressor, and suppressing the fan speed.

Once the operation is set, the setting is preserved until you press this button

again to stop the operation, even if the indoor unit operation is stopped.

on the remote controller display shows that the unit is in

OUTDOOR UNIT LOW NOISE mode.

Notes:

• This operation cannot be performed simultaneously with FAN, DRY

and POWERFUL operation modes.

• This operation cannot be performed on a multi-type air conditioner.

If this mode is unintentionally set on a multi-type air conditioner,

cancel the setting by pressing the button. Otherwise, the signal of

the remote controller cannot be transmitted properly.

19 ECONOMY button

Starts or stops ECONOMY operation that saves more electricity

than other operation modes by changing the set temperature to a

moderate setting.

By pressing the ECONOMY button, the ECONOMY indicator on the

indoor unit turns on.

• In COOL or DRY mode, the room temperature will be adjusted a few

degrees higher than the set temperature.

• In HEAT mode, the room temperature will be adjusted a few

degrees lower than the set temperature.

• Especially in COOL or DRY mode, you can have improved

dehumidification without significantly lowering the room temperature.

Notes:

• In COOL, HEAT, or DRY mode, the maximum output of this

operation is approximately 70 % of usual air conditioning operation.

• This operation cannot be performed during temperature monitoring

by AUTO mode.

• In multi-type air conditioning system, ECONOMY operation is

performed only on the indoor unit whose ECONOMY button on the

corresponding remote controller is pressed.

20 SENSOR button (ENERGY SAVING)

Activates or deactivates the energy saving.

* The Energy Saving is ON at the time of purchase.

: The setting must be done while the setting screen is displayed for

each function.

: The button is controllable only when the air conditioner is on.

See page 5

See page 3

See page 5

See page 3

See page 8