Fujitsu Lifebook E4000 Bios-Handbuch - Seite 2

Blättern Sie online oder laden Sie pdf Bios-Handbuch für Laptop Fujitsu Lifebook E4000 herunter. Fujitsu Lifebook E4000 29 Seiten. Lifebook e series

Seite drucken

L i f e B o o k E S e r i e s B I O S

E Series BIOS

BIOS SETUP UTILITY

The Built-in Operating System (BIOS) Setup Utility is a

program that sets up the operating environment for

your notebook. Your BIOS is set at the factory for

normal operating conditions, so normally there is no

need to set or change the BIOS environment to operate

your notebook.

The BIOS Setup Utility configures:

Device control feature parameters, such as changing

I/O addresses and boot devices.

System Data Security feature parameters, such

as passwords.

Entering the BIOS Setup Utility

To enter the BIOS Setup Utility do the following:

1. Turn on or restart your notebook.

2. Press the [F2] key once the Fujitsu logo appears on

the screen with a prompt below it. This will open the

main menu of the BIOS Setup Utility with the

current settings displayed.

3. Press the arrow keys to scroll through the other

setup menus to review or alter the current settings.

Navigating Through The Setup Utility

The BIOS setup utility consists of six menus: Main,

Advanced, Security, Boot, Info, and Exit. This document

explains each menu in turn, including all submenus and

setup items.

The following procedures allow you to navigate the

setup utility menus:

1. To select a menu, use the left and right cursor keys:

[

], [

2. To select a field within a menu or a submenu, use the

up and down cursor keys:

3. To select the different values for each field, press the

[Spacebar] or [+] to change to the next higher selec-

tion and [F5] or [-] to go to the next lower selection.

4. To activate a submenu press the [Enter] key.

5. To return to a menu from a submenu, press [Esc].

6. To go to the Exit menu from any other menu,

press the [Esc] key.

[ ], [ ].

P O I N T S

Selecting a field causes a help message about that

field to be displayed on the right-hand side of the

screen.

Pressing the Enter key with the highlight on a selec-

tion that is not a submenu or auto selection will cause

a list of all options for that item to be displayed.

Pressing the Enter key again will select the high-

lighted choice.

7. Pressing the [F9] key resets all items in the BIOS to

the default values.

8. Pressing the [F10] key saves the current configura-

tion and exits the BIOS Setup Utility. You will be

asked to verify this selection before it is executed.

9. Pressing the [F1] key gives you a general help screen.

Entering the Setup Utility After a Configuration

Change or System Failure

If there has been a change in system configuration that

does not agree with the parameter settings stored in your

BIOS memory, or there is a system failure, the system

beeps and/or displays an error message after the Power

On Self Test (POST). If the failure is not too severe, it

will give you the opportunity to modify the settings of

the setup utility, as described in the following steps:

1. When you turn on or restart the computer there is a

beep and/or the following message appears:

Error message - please run SETUP

program Press <F1> key to continue,

<F2> to run SETUP

2. If an error message is displayed on the screen, and

you want to continue with the boot process and start

the operating system anyway, press the [F1] key.

P O I N T S

If your notebook emits a series of beeps that sounds

like a code and the display is blank, refer to the

Troubleshooting Section in the system User's Guide.

The Troubleshooting Section includes a list of error

messages and their meanings.

If your data security settings require it, you may be

asked for a password before the operating system will

be opened.