Brother HL-5450DN Handbuch zur Schnelleinrichtung
Blättern Sie online oder laden Sie pdf Handbuch zur Schnelleinrichtung für Druck-Server Brother HL-5450DN herunter. Brother HL-5450DN 2 Seiten. Zlt
Auch für Brother HL-5450DN: Handbuch zur Schnelleinrichtung (2 seiten), Benutzerhandbuch (23 seiten), Installationshandbuch (16 seiten), Handbuch zur Produktsicherheit (23 seiten)
Seite drucken
CHN-ENG
Version 0
1
Unpack the machine and check the components
•
•
•
Start Here
•
•
WARNING indicates a potentially
WARNING
hazardous situation which, if not avoided,
could result in death or serious injuries.
•
CAUTION indicates a potentially
CAUTION
hazardous situation which, if not avoided,
may result in minor or moderate injuries.
USB cable
It is recommended to use a USB 2.0 (Type A/B) interface cable that is no longer than 2 meters.
Parallel cable (HL-5440D and HL-5445D only)
DO NOT use a parallel interface cable that is longer than 2 meters. Use a shielded interface cable
that is IEEE 1284-compliant.
Network cable (HL-5450DN only)
Use a straight-through Category 5 (or greater) twisted-pair cable for 10BASE-T or 100BASE-TX
Fast Ethernet Network.
2
Remove the packing material from the machine
Important
DO NOT plug in the AC power cord yet.
a.
Remove the packing tape from the outside of the machine.
b.
Open the MP tray a, and remove the packing tape b from the MP tray
support, then close the MP tray.
3
Load paper in the paper tray
a.
Pull the paper tray completely out of the machine.
b.
While pressing the green paper-guide release lever a, slide the paper guides
to fit the paper size you are loading in the tray. Make sure that the guides are
firmly in the slots.
4
Print a test page
Important
DO NOT connect the Interface cable yet.
a.
Connect the AC power cord to the machine and then connect it to an AC power
outlet.
Please read the Product Safety Guide first, then read this Quick Setup Guide for the correct setup and installation
procedure. To view the Quick Setup Guide in other languages, please visit http://solutions.brother.com/.
Note
The components included in the box may differ depending on your country.
We recommend that you save the original packaging.
If for any reason you must ship your machine, carefully repack the machine in the original
packaging to avoid any damage during transit. The machine should be adequately insured with
the carrier. For how to repack the machine, see Packing and shipping the machine in the User's
Guide.
Illustrations in this Quick Setup Guide are based on the HL-5450DN.
To ensure safe operation the supplied plug must be inserted only into a standard power outlet
that is properly grounded through the standard electrical wiring. Non grounded equipment may
cause an electrical shock hazard, and may cause excessive electrical noise radiation.
The interface cable is not a standard accessory. Buy the appropriate interface cable for the
Product Safety Guide
connection you want to use (parallel (HL-5440D and HL-5445D only) or Network (HL-5450DN
only)).
USB Interface Cable
c.
d.
Press the front cover release button and open the front cover. Remove the
silica gel pack a.
e.
CAUTION
DO NOT eat the silica gel pack. Please throw away. If ingested, seek medical attention
immediately.
c.
e.
Fan the stack of paper well to avoid paper jams and misfeeds.
d.
Put the paper in the tray and make sure:
The paper is below the maximum paper mark (▼▼▼) a. Over filling the
paper tray will cause paper jams.
The side to be printed on is face down.
The paper guides touch the sides of the paper so it will feed properly.
b.
d.
Turn the machine's power switch on.
c.
After the machine has finished warming up, the Ready LED stops blinking and
stays green.
WARNING
•
Plastic bags are used in the packing of your machine. Plastic bags are not toys. To
avoid the danger of suffocation, keep these bags away from babies and children
and dispose of them correctly.
Drum Unit and Toner
Quick Setup Guide
•
If you use a Lower Tray, DO NOT carry the machine with the Lower Tray as you may
Cartridge Assembly
be injured or cause damage to the machine because it is not attached to the Lower
(pre-installed)
Tray.
Note
Keep a minimum gap around the machine as shown in the illustration.
AC Power Cord
Installer CD-ROM
150 mm
f.
Take out the drum unit and toner
Hold the drum unit and toner cartridge
cartridge assembly.
assembly level with both hands and
gently shake it from side to side
several times to distribute the toner
evenly inside the cartridge.
g.
Remove the orange protective
Put the drum unit and toner cartridge
material from the drum unit and toner
assembly firmly back in the machine.
cartridge assembly.
h.
Close the front cover of the machine.
f.
Put the paper tray firmly back in the machine. Make sure that it is completely
Lift up the support flap a to prevent paper from sliding off the face-down
inserted into the machine.
output tray.
For more information about recommended paper, see Recommended paper in
the User's Guide.
Press Go. The machine will print a test page. Check that the test page has
printed correctly.
Note
This function will not be available after the first print job you send from your computer.
Printer LED Indications
Back Cover
Toner
Drum
Paper
Error
Ready
150 mm
150 mm
150 mm
Back Cover
Toner
Drum
Paper
Error
Ready
Back Cover
Toner
Drum
Paper
Error
Ready
1 The LED will blink ON and OFF at 1 second intervals.
2 The LED will blink ON and OFF at 0.5 second intervals.
3 The yellow LED will blink in a pattern of ON for 2 seconds and then OFF for 3 seconds.
The machine continues printing until the LED indicates the replace toner message.
Options
The machine has the following optional accessories. You can expand the capabilities of the machine by adding
these items. For more information about the optional Lower Tray Unit and compatible SO-DIMM Memory, visit us at
http://solutions.brother.com/.
For installing the SO-DIMM Memory, see Installing extra memory in the User's Guide.
The lower paper tray unit can hold up to 500 sheets of
paper. When the tray is installed, the machine expands
total input capacity up to 800 sheets.
Consumables
When the time comes to replace consumable items, an error will be indicated by the LEDs on the control panel. For
more information about the consumables for your machine, visit us at http://www.brother.com/original/ or contact
your local Brother reseller.
For replacing the consumable items, see Replacing consumable items in the User's Guide.
Turn the sheet over to install the printer driver.
Quick Setup Guide
HL-5440D
HL-5445D
HL-5450DN
Blinking:
or
or
ON:
or
or
OFF:
Sleep/
Warming Up/
Receiving Data/
OFF
Ready
Deep Sleep
Cooling Down
Data Remaining
1
2
Dimmed
Drum End
Toner Low
3
Replace Toner
Drum Stop
Drum Error
2
Soon
3
Front Cover
Back Cover
Service Call
Jam Inside
No Paper
Jam Rear
2
2
Open
Open
2
Error
2
SO-DIMM Memory
Lower Tray Unit
(HL-5450DN only)
LT-5400
You can increase the memory by installing one
SO-DIMM (Small Outline Dual In-line Memory
Module).
Toner cartridge
Drum unit
Standard Toner: TN-3335
DR-3350
High Yield Toner: TN-3385