Indesit DSR 57B GB Betriebsanleitung - Seite 8

Blättern Sie online oder laden Sie pdf Betriebsanleitung für Geschirrspüler Indesit DSR 57B GB herunter. Indesit DSR 57B GB 16 Seiten.

Seite drucken

Refined Salt and Rinse Aid

Only use products which have been specifically designed

for dishwashers. Do not use table salt or industrial salt.

(Follow the instructions given on the packaging.)

If you are using a multi-function product, we recommend

that you add salt in any case, especially if the water is hard

or very hard. (Follow the instructions given on the packaging.)

If you do not add salt or rinse aid, the LOW SALT

LOW RINSE AID

indicator lights will remain lit.

Measuring out the refined salt

The use of salt prevents the formation of LIMESCALE on the

dishes and on the machine's functional components.

• It is important that the salt dispenser be never empty.

• It is important to set the water hardness.

The salt dispenser is located in the lower part of the dishwasher

(see Description)

and should be filled:

• When the LOW RINSE AID indicator light in the control panel

is lit

;

• When the green float

longer visible.

• See autonomy in the water hardness table.

1. Remove the lower rack and unscrew the

container cap (anticlockwise).

2. Only the first time you do this: fill the water

dispenser up to the edge.

3. Position the funnel

fill the salt container right up to its edge

(approximately 1 kg); it is not unusual for a little water to leak out.

4. Remove the funnel and wipe any salt residue away from the

opening; rinse the cap under running water and then screw it on.

It is advisable to perform this procedure every time you add salt

to the container.

Make sure the cap is screwed on tightly, so that no detergent can

get into the container during the wash cycle (this could damage

the water softener beyond repair).

Whenever you need to add salt, we recommend carrying out

the procedure before the washing cycle is started.

Setting the water hardness

For perfect water softener operation, it is essential that the

adjustment be based on the water hardness in your house. Ask

your local water supplier for this information. The factory setting

is for medium water hardness.

• Switch the dishwasher on using the On/Off button.

• Switch it off using the On/Off button

• Hold down the START/PAUSE button

you hear a beep.

• Switch it on using the On/Off button

• The display shows the current selection level number and the

salt indicator light.

• Press button P to select the desired hardness level (see

Hardness Table).

• Switch it off using the On/Off button

• Setting is complete!

Only available in selected models.

on the cap of the salt dispenser is no

(see figure)

for 5 seconds until

Water Hardness Table

level

°dH

0 - 6

6 - 11

11 - 20

3 12 - 17

21 - 30

4 17 - 34

31 - 60

and

5 34 - 50

61 - 90

For values between 0°f and 10°f, we do not recommend the use

of salt. A setting of 5 may increase cycle duration.

(°dH = hardness measured in German degrees - °f = hardness

measured in French degrees – mmol/l = millimoles per litre)

Measuring out the rinse aid

Rinse aid makes dish DRYING easier. The rinse aid dispenser

should be filled:

• When the LOW RINSE AID indicator light on the panel/display

;

is lit

• When the dark optical indicator on the dispenser door "E"

becomes transparent.

and

NEVER pour the rinse aid directly into the tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results, you

can adjust the quantity of rinse aid used. Turn the adjuster "F".

A maximum of 4 levels can be set according to the dishwasher

model. The factory setting is for a medium level.

• If you see bluish streaks on the dishes, set a low number (1-2).

• If there are drops of water or limescale marks on the dishes,

set a high number (3-4).

Average autonomy

salt dispenser with 1

wash cycle per day

°fH

mmol/l

months

0 - 10

0 - 1

7 months

1.1 - 2

5 months

2.1 - 3

3 months

3.1 - 6

2 months

6.1 - 9

2/3 weeks

1. Open the dispenser by turning

the cap "G" in an anticlockwise

direction.

2. Pour in the rinse aid, making

sure it does not overflow from the

dispenser. If this happens, clean

the spill immediately with a dry

cloth.

3. Screw the cap back on.