Indesit IDL 60 Handbuch für Installation und Gebrauch - Seite 8

Blättern Sie online oder laden Sie pdf Handbuch für Installation und Gebrauch für Geschirrspüler Indesit IDL 60 herunter. Indesit IDL 60 17 Seiten. Dishwasher
Auch für Indesit IDL 60: Handbuch für Installation und Gebrauch (44 seiten)

Seite drucken

Indesit IDL 60 Handbuch für Installation und Gebrauch

Turning on the Appliance

First of all.

Turn on the water tap completely and press ON-OFF button

"A". you will hear a short beep and indicator light "B" lights

up.

Now the appliance is on and awaiting instructions.

Starting and selecting the cycle.

Turn the cycle selector knob "D" clockwise until the reference

notch on the knob corresponds with the number or symbol

for the cycle you wish to set (consult the wash cycle table on

page 7, especially when first using the appliance).

If the appliance door is shut, press the Start button "R" and

you will hear a beep; the cycle will start up within a few

seconds.

Cycle phase indicator lights

The dishwasher is provided with 4 indicator lights "G" which

come on in sequence as the appliance is performing that

specific phase of the wash cycle.

These phases are:

pre-wash,

wash,

Cancelling or modifying a wash cycle in progress.....

Premise: You can cancel the wash cycle in progress, if it has

only just started.

To modify a wash cycle, keep the RESET button "R" pressed

for about 5 seconds: a prolonged beep will sound, followed

by three short beeps. Indicator light "G" will turn off and at

this point, all the settings will have been cancelled.

To select a new wash cycle, repeat the operations illustrated

in the paragraph entitled "starting and selecting the cycle".

Warning: the knob must be turned clockwise from wash

cycle 1 to 6, an anti-clockwise from wash cycle 6 to 1.

If you have left out a dish...

You can interrupt a wash cycle by pressing the ON-OFF

button, then place the dishes you had left out into the

appliance, which will start up from where it was interrupted

when you turn it back on.

There's been a power failure? Have you opened the

dishwasher door?

The wash cycle stops and then restarts when the electricity

comes back on or when the door is shut.

rinses,

drying

At the end of the wash cycle....

The end of the wash cycle is indicated by two short beeps

and the flashing of the drying phase indicator light.

Warning:

Turn the appliance off by pressing button "A", unplug the

appliance from the electricity socket to cut off the power

supply; the power supply cable should consequently be

easily accessible.

• Turn off the water tap.

• Wait a few minutes before unloading the dishes: if you

wait a little while, they dry better thanks to the steam.

• Empty the lower rack first.

Warning: when you open the dishwasher door after the wash

cycle has just ended or is under way, take care not to scald

yourself with the hot steam.

You decide when it starts.

When you have loaded the dishes, you can choose when to

start your dishwasher before setting the wash cycle desired.

Press button "H" to delay the start of the wash cycle by 12,

9, 6 or 3 hours. Each time you press it, you will hear a short

beep and the indicator light "G" corresponding to the

selected delay will come on.

Now you can select the desired wash cycle and, after you

hear the beep, the countdown to the delayed start will begin.

If you have set a 12 hour delay, for example, once you have

selected the wash cycle, the 12 hour indicator light will flash

followed by the others in sequence until the set time delay is

up. A quick look at the indicator lights will keep you informed

of the countdown progress at all times.

Dual function of indicator lights "G"

1) flashing to indicate a delayed start: to remind you

that you have set a delayed start;

2) on and not flashing beneath the cycle phase symbol:

meaning the cycle has started and is in the phase indicated

by the symbol.

Have you changed your mind?

If you change your mind, you can set a shorter time delay:

press button "H" to select it. You need not reset the wash

cycle.

If on the other hand you want to cancel the delay set and

you want the cycle to start immediately, press button "H"

repeatedly until the cycle starts and indicator light "G"

corresponding to the cycle start phase comes on.