Indesit ID60C2 AA Betriebsanleitung - Seite 3

Blättern Sie online oder laden Sie pdf Betriebsanleitung für Herde Indesit ID60C2 AA herunter. Indesit ID60C2 AA 28 Seiten. Free standing electric cooker

Seite drucken

Installation

WARNING - THIS APPLIANCE MUST BE EARTHED.

Mains Connection

Your cooker should have been checked to ensure

that the voltage corresponds with your supply

voltage, this is stated on the rating plate, which is

situated on the outer rear panel.The model number

and the serial number are located on the front of the

cooker, as shown on the Features page.

The cooker must be connected by a competent

person such as one who is a, NICEIC registered

contractor to a suitable double-pole control unit with

a minimum rating of 32A and a minimum contact

clearance of 3mm (applicable to newer properties,

older properties where a 30A double pole control unit

and a minimum contact clearance of 3mm is

acceptable).

The double pole control unit should be fitted

adjacent to the cooker, in accordance with IEE

regulations.The control unit must be within 2 metres

of but not directly above the appliance and should

be easily accessible in the event of an emergency.

The power supply cable should conform to B.S.6004

with a conductor size of 6mm

Access to the mains terminals is gained by

removing the rear access cover. The mains cable

must pass through the cable clamp adjacent to the

terminal block. Sufficient cable should be used to

allow the cooker to be pulled out for servicing.

Ensure that the mains cable is routed away from

any brackets affixed to the rear panel and is not

trapped to the rear wall when pushing the cooker

into position between cabinets.

For the installation of the feeding cable carry out the

, minimum.

following operations:

1 Open the terminal

board by inserting a

screwdriver into the

bottom tabs of the

cover. Use the

screwdriver as a lever

by pushing it down to

open the cover (see

diagram).

2 Loosen the cable

clamp screw and

remove it, using a

screwdriver as a lever

(see figure).

3. Fasten the wires

under the screw heads,

respecting

the colour code:

Black/Blue (N), Red/Brown (L) and Bare Wire/Yellow-

Green (

 Once the connections have been made, tighten all

the terminal screws fully.

Fasten the supply cable in place with the clamp

and close the cover of the terminal board.

Levelling

Four feet are fitted which can be adjusted up or

down to set the height (900mm - 930mm) and level

the cooker.

The feet can be simply screwed in or out to lower or

raise the cooker.

After the correct height is achieved, lock the feet

into position by tightening the locking nut using an

open ended spanner.

CAUTION: Some soft floor coverings may get

damaged if the cooker is not moved carefully.

NOTE: Ensure oven shelves are level by using a

spirit level on the rod shelves.

Siting the Cooker

The cooker is designed to fit between kitchen

cabinets spaced 600mm apart.

The space either side need only be sufficient to

allow withdrawal of the cooker for servicing and

cleaning. It can be used with cabinets one side or

both as well as in an angled corner setting.

It can also be used freestanding.

Adjacent side walls which project above hob level,

must not be nearer to the cooker than 150mm and

should be protected by heat resistant material. Any

overhanging surface or cooker hood should not be

nearer than 650mm.

Note: This appliance must NOT be fitted on a

platform.

Moving the Cooker

Note: Take care in moving the cooker as it is

heavy.Take care to ensure that any floor

covering is not damaged.

Before moving your

cooker, switch off at

the cooker control

unit, ensure that it is

cool.

Open the grill door

sufficiently to allow a

comfortable grip on

the underside front

edge of the oven

roof, avoiding any

grill elements.