Indesit K 3G2/G Handbuch für Installation und Gebrauch - Seite 6
Blättern Sie online oder laden Sie pdf Handbuch für Installation und Gebrauch für Herde Indesit K 3G2/G herunter. Indesit K 3G2/G 17 Seiten. Indesit cookers operating instructions
Auch für Indesit K 3G2/G: Handbuch für Installation und Gebrauch (17 seiten), Betriebsanleitung (12 seiten), Betriebsanleitung (12 seiten)
Seite drucken
Adapting the cooker to different types of gas
In order to adapt the cooker to a different type of gas with
respect to the gas for which it was produced (indicated on
the label attached to the lid), follow these steps:
a) replace the hose holder mounted on the appliance with
that supplied in the bag of "cooker accessories".
Important: the hose holder for liquid gas is marked 8, the
hose holder for methane gas is marked 13. Always fit the
sealing gasket.
b) Replacing the burner nozzles on the hob:
•
remove the grids and slide the burners from their
housings;
•
unscrew the nozzles using a 7 mm socket spanner,
and replace them with nozzles for the new type of gas
(see table 1 "Burner and nozzle characteristics").
•
replace all the components by repeating the steps in
reverse order.
c) Minimum regulation of the hob burners:
•
turn the tap to minimum;
•
remove the knob and adjust the regulation screw, which
is positioned in or next to the tap pin, until the flame is
small but steady.
N.B.: in the case of liquid gas, the regulation screw
must be screwed in to the bottom.
•
check that the flame does not turn off when you turn
the tap quickly from high to low.
d Regulating the primary air of the burners:
The primary air of the burners requires no regulation.
Adapting the gas oven to different types of gas
a) Replacing the oven burner nozzle:
•
remove the warming drawer;
•
remove the sliding protection "A" (see Fig.C);
•
remove the screw and then the oven burner "V"(see
Fig. D). Remove the oven door to facilitate this
operation.
•
unscrew the oven burner nozzle using the special
socket spanner for the nozzles (see Fig. E), or better
still a 7 mm socket spanner, and replace it with a nozzle
suited to the new type of gas (see table 1).
A
Fig. C
b) Minimum regulation of the gas oven burner with
thermostat (see fig.):
•
light the burner as described in the paragraph "the oven
knob" of the instruction booklet.
•
turn the knob to Max for about 10 minutes and then
turn the knob to the Min setting;
•
remove the knob;
•
regulate the screw positioned outside the thermostat
pin until the flame is small but steady.
N.B.: in the case of liquid gas, the regulation screw
must be screwed in to the bottom.
•
check that the burner does not turn off when you turn
the knob from Max to Min and and when you open
and close the oven door quickly.
Adapting the gas grill to different types of gas
Replacing the nozzle of the grill burner:
•
remove the screw and then slide out the grill burner "V"
(see Fig. F);
•
unscrew the grill burner nozzle using the special socket
spanner for the nozzles (see Fig. G) or better still a 7 mm
socket spanner; replace the nozzle with a nozzle for the new
type of gas (see table 1).
V
Important: when mounting the grill burner check that there is a
space of at least 4 mm between the security thermocouple (if
installed) and the burner.
Fig. D
6
Fig.E
V
Fig. F
I
Fig. G