Indesit KG 6408 WV/G Handbuch für Installation und Gebrauch - Seite 3
Blättern Sie online oder laden Sie pdf Handbuch für Installation und Gebrauch für Herde Indesit KG 6408 WV/G herunter. Indesit KG 6408 WV/G 12 Seiten. Indesit cooker with ventilated oven instructions for installation and use
Seite drucken
All instruction on the following pages must be carried out by
a competent person (corgi registered) in compliance with
gas safety (installation and use) regulation 1984.
Important: disconnect the cooker from the electrycity
and gas supply when any adjustment, etc.
Positioning
Important: this unit may be installed and used only in
permanently ventilated rooms according to the British
Standards Codes Of Practice: B.S. 6172/B.S. 5440, Par. 2
and B.S. 6891 Current Editions. The following requirements
must be observed:
a) The cooker should not be installed in a bed sitting room
with a volume of less than 20m
of volume less than 5m
110cm
2
is required, if it is installed in a room of volume
between 5m
3
and 10m
50cm
2
is required, while if the volume exceeds 11m
airvent is required. However, if the room has a door or a
window vhich opens directly to the outside no air vent is
required even when the volume is between 5m
b) During prolonged use of the appliance you may consider
it necessary to open a window to the outside to improve
ventilation.
c) If there are other fuel burning appliances in the same
room, B.S.5440 Part 2 Current Edition, should, be
consulted to determine the requisite air vent requirements.
Installation of the cooker
The cooker is prepared with protection degree against
excessive heating of type X, the appliance can therefore be
installed next to cabinets, provided the height does not exceed
that of the hob. If the cooker is placed touching walls or sides
of neighbouring cabinets, these must be capable of
withstanding a temperature rise of 60°C above room tempe-
rature. Levelling feet supplied with the cooker, can be fitted
to the cooker to accomodate uneven floors. See fitting
instruction on feet packing. For a correct installation of the
cooker the following precautions must be followed:
a) The cooker may be located in a kitchen, a kitonen/diner
or bed sitting room, but not in a bathroom or shower room.
b) The furniture units next to the cooker, that is higher than
the working boards, must be placed at least 110 mm from
the edge of the board. Curtains must not be fitted
immediately behind the cooker or within 110 mm. of the
sides of the cooker.
c) The hoods must be installed according to the
requirements in the hood handbook.
d) Wall cabinets may be fitted in line with the sides of the
base units, providing that the lower edge of the wall cabinet
is a minimum of 420 mm. above the worktop. The
minimum distance combustible material kitchen units can
be fitted directly above the worktop is 700 mm. (see Fig.
A)
e) The wall in contact with the back of the cooker must be of
flameproof material.
f) The cooker is fitted with the a safety chain that must be
attached to a hook, secured to the wall behind the
appliance (see Fig. B).
Installation instructions
3
. If it is installed in a room
3
an air vent of effective area of
3
a supplementary airvent area of
3
and 11m
HOOD
600
Min.
mm.
Fig. A
Connecting the gas
3
no
The cooker should be connected to the gas-suply by a corgi
registered installer. During installation of this product it is
essential to fit an approved gas tap to isolate the supply from
3
.
the appliance for the convenience of any subsequent removal
or servicing. Connection of the appliance to the gas mains
or liquid gas must be carried out according to the prescribed
regulation in force, and only after it is ascertained that it is
adaptable to the type of gas to be used. If not, follow the
instructions indicated in the paragraph headed "Adaptation
to different gas types". In the case of connection to liquid
gas, by tank, use pressure regulators that conform to the
regulation in force. The gas supply must be connected to the
right of the appliance. Be sure that the hose does not pass
through the rear of the cooker touching hot parts.
Important: make sure the supply pressure conforms with
the values shown in the table entitled "Caracteristics of the
burners and nozzles".
When the cooker is installed between cabinets (recessed),
the gas connection must be effected by an approved flexible
hose with bayonet fitting (BS 669 Current Edition). The gas
inlet for the cookers is a threaded G 1/2 gas female fitting.
Connecting the gas supply
To make the connection, a flexible hose should be used
corresponding to the current gas regulations which are:
the hose must never be at any point in its lenght in contact
·
with the "hot" parts of the cooker;
the hose must never be longer than 1.5 metre;
·
the hose must not be subject to any tension or torsional
·
stress and it must not have any excessively narrow curves
or bottlenecks;
the hose must be easy to inspect along its entire lenght
·
to check its condition;
the hose must always be in good condition, never attempt
·
to repair.
Important: the installation must comply with gas safety
(installation and use) regulations 1984. In all cases for the
above, by low, a qualified, corgi approved engineer must be
called for installation.
3
Fig. B