Indesit PI 640 A GB Betriebsanleitung - Seite 4

Blättern Sie online oder laden Sie pdf Betriebsanleitung für Kochfeld Indesit PI 640 A GB herunter. Indesit PI 640 A GB 12 Seiten. Indesit hob operating instruction
Auch für Indesit PI 640 A GB: Betriebsanleitung (13 seiten), Betriebsanleitung (12 seiten), Betriebsanleitung (12 seiten)

Seite drucken

Gas Connection

The cooktop should be connected to the gas supply

by an authorized installer. During installation of this

product it is essential to fit an approved gas tap to

isolate the supply from the appliance for the

convenience of any subsequent removal or servicing.

Connection of the appliance to the gas mains or liquid

gas tanks must be carried out according to the safety

standards currently in force, and only after it is

ascertained that it is suitable for the type of gas to be

used. If not, follow the instructions indicated in the

section entitled, Adapting the Cooktop for Different

Types of Gas. If the cooktop is to be connected to

tanks containing liquid gas, use pressure regulators

that comply with current safety standards.

To insure that the appliance operates safety, the gas

is regulated correctly and your appliance lasts over

time, make sure that gas pressure levels comply with

the indications given in Table 1, Nozzle and Burner

Specifications.

Gas Connection to Non-flexible Pipe

(copper or steel)

Connection to the gas source must be done in such

a way as to not create any stress points at any part of

the appliance.

The appliance is fitted with an adjustable, "L" shaped

connector and a gasket for the attachment to the gas

supply. Should this connector have to be turned, the

gasket must be replaced (supplied with the

appliance).

The gas feed connector to the appliance is a

threaded, male 1/2" connector for round gas pipe.

Gas Connection to .lexible Steel Pipe

The gas feed connector to the appliance is a

threaded, male 1/2" connector for round gas pipe.

Only use pipes, tubes and gaskets that comply with

current safety codes. The maximum length of the

flexible pipes must not exceed 2000 mm. Once the

connection has been made, ensure that the flexible

metal tube does not touch any moving parts and is not

crushed.

Check the Seal

Once the appliance has been installed, make sure

all the connections are properly sealed, using a soapy

water solution. Never use a flame.

Adapting the Cooktop for Different Types of Gas

To adapt the cooktop to a different type of gas than

that for which it was designed, (see the sticker under

the hob or on the packaging), the burner nozzles must

be changed, as follows:

1. Remove the pan supports and slide the burners out

of the cooktop.

2. Unscrew the nozzles using a 7mm socket wrench

and replace them with those for the new type of

gas. (See table 1, Burner and Nozzle

Specifications).

3. Reassemble the parts following the instructions in

reverse order.

4. On completing the operation, replace the old rating

label with the one showing the new type of gas; the

sticker is available from our Service Centres.

Regulation of Air Supply to the Burner

The burners do not need a primary air regulator.

Minimum Regulation

1. Turn the gas valve to minimum.

3. Make sure that, when the knob is turned rapidly

high to low, the flame does not go out.

4. In the event of a malfunction on appliances with the

security device (thermocouple) when the gas

supply is set at minimum, increase the minimum

supply levels using the regulator screw.

In the case of liquid gas, the regulation screw must

be fully screwed in (clockwise).

Once the adjustment has been made, apply sealing

wax, or a suitable substitute, to the old seals on the

by-pass.

2. Remove the knob

and turn the regulator

screw (positioned either

on the side of the top or

inside the shaft)

clockwise until the flame

becomes small but

regular.