Kohler 24271T-CP Installationsanleitung Handbuch - Seite 9
Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Sanitärprodukt Kohler 24271T-CP herunter. Kohler 24271T-CP 14 Seiten. Oblo sensor faucet
Seite drucken
安装结果检查
检查并确保所有衔接处都已拧紧，打开排水系统
和主要供水源，检查并修理有漏水的接口。
清理说明
适用于所有加工处理过的表面，以中性肥皂水清
洗镀层表面，再以干净的软布彻底擦干整个表面。
许多清洁剂，比如氨水，去污粉及洁厕灵等，会
对电镀表面造成伤害，切忌使用。
有腐蚀性的清洁剂或溶剂不可使用于科勒的水龙
头及其配件上。
用户须知
1. 感应指示灯的各种闪烁情况
感应指示灯是使用者了解感应龙头有效、
唯一的途径。所以明白了感应指示灯闪烁
所代表的含义，可以正确使用感应龙头，
如图示:
(1) 快速闪烁，代表感应龙头正处于通电
后的30秒自动调节阶段。期间，安装者、
使用者不得干扰其自动调节，感应范围
内不要放置物体。
(2) 间隔6秒钟闪烁一次（直流版本），
表示电池即将使用完，请更换电池。
(3) 间隔2秒钟连续闪烁：若直流感应龙
头, 代表龙头电池耗尽，已停止工作，等
待使用者更换电池;若交流感应龙头，表
示为两种情况：一种为刚刚停电；另一
种为在交流供电正常的情况下，则电源
盒直流接线端接触不良。
(4) 在正常工作情况下，当有物体被感应
时，龙头出水，感应指示灯闪烁一次。
（龙头关闭，感 应指示灯不闪烁。）
2.
超时出水控制
连续在感应状态下使用约一分钟，龙头自动止水。
自动止水后，手或物体离开感应范围后，再次进
入感应范围内，龙头正常工作，否则无反应。
1364728-T01-A
INSTALLATION CHECKOUT
Check and ensure that all connections are tight. Open the
drain. Turn on main water supply and check for leaks.
Replace as required.
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with a mild soap and warm
water. Wipe entire surface completely dry with a clean soft
cloth. Many cleaners may contain chemicals, such as
ammonia, chlorine, toilet cleaner etc. which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets
and fittings.
IMPORTANT CONSUMER INFORMATION
1. Note of the Indicator Flashing
The indicator is the only and effective way to learn
the faucet's working conditions. So the users can
use the sensor faucet correctly with knowing the
meaning of the sensor indicator's flashing.
(1) Quick flashing means the faucet is in the
period of adjusting sensing distance after power
on for 30s. During these 30s, please do not
disturb auto adjustment or place objects within the
sensing range.
指示灯
(2) The indicator flashes every 6 seconds (DC
Indicator Light
type) indicates that the unit is out of battery and
has stopped working. Replease batteries.
(3) The indicator flashes every 2s: as for DC type
faucets, this indicates the unit is out of battery
and ceases working. Please replace batteries.
For AC faucet, it indicates two possibilities: one
is that the unit is out of battery; or poor DC
terminal contact under normal AC power supply.
(4) In normal condition, the water will flow and
the indicator will flash one time when objects are
inducted. (The indicator does not flash when
faucet stops flowing.)
2. Overtime Flowing Control
When the faucet works for about 1 minute continuously, the
water will be shut off automatically. After that, objects must
be removed from the sensing range. Then the water will
flow when objects go into the sensing range again.
Otherwise, the faucet will not work.
9