Kohler Command Pro CV200 Benutzerhandbuch - Seite 6
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Motor Kohler Command Pro CV200 herunter. Kohler Command Pro CV200 8 Seiten.
Auch für Kohler Command Pro CV200: Benutzerhandbuch (48 seiten)
Seite drucken
Check Oil Level
NOTE: To prevent extensive engine wear or
damage, never run engine with oil level
below or above operating range
indicator on dipstick.
Ensure engine is cool and level. Clean oil fi ll
cap/dipstick areas of any debris.
1. Remove dipstick; wipe oil off .
2. Reinsert dipstick into tube; press completely
down and turn 1/4 turn.
3. Remove dipstick; check oil level. Level
should be at top of indicator on dipstick.
4. If oil is low on indicator, add oil up to top of
indicator mark.
5. Reinstall and secure dipstick.
Change Oil and Filter
Change oil while engine is warm.
1. Clean area around oil fi ll cap/dipstick and
drain plug. Remove drain plug and oil fi ll cap/
dipstick; drain oil into appropriate container.
2. Clean area around oil fi lter. Remove clean oil
change screw; then slowly remove fi lter; wipe
off mounting surface.
3. Apply thread sealant around three full
threads of drain plug; reinstall drain plug.
Torque to 120 in. lb. (13.6 N·m).
4. Reinstall clean oil change screw. Torque to
130 in. lb. (14.7 N·m).
5. Apply a thin fi lm of clean oil to rubber gasket
on new fi lter.
6. Refer to instructions on oil fi lter for proper
installation.
7. Fill crankcase with new oil. Level should be
at top of indicator on dipstick.
8. Reinstall oil fi ll cap/dipstick and tighten
securely.
9. Start engine; check for oil leaks. Stop engine;
correct leaks. Recheck oil level.
10. Dispose of used oil and fi lter in accordance
with local ordinances.
6
Fuel Recommendations
Gasoline is extremely fl ammable and
its vapors can explode if ignited. Store
gasoline only in approved containers, in
well ventilated, unoccupied buildings, away
from sparks or fl ames. Spilled fuel could
ignite if it comes in contact with hot parts or
sparks from ignition. Never use gasoline as a
cleaning agent.
NOTE: E15, E20 and E85 are NOT approved
Fuel must meet these requirements:
● Clean, fresh, unleaded gasoline.
● Octane rating of 87 (R+M)/2 or higher.
● Research Octane Number (RON) 90 octane
minimum.
● Gasoline up to 10% ethyl alcohol, 90%
unleaded is acceptable.
● Methyl Tertiary Butyl Ether (MTBE) and
unleaded gasoline blend (max 15% MTBE by
volume) are approved.
● Do not add oil to gasoline.
● Do not overfi ll fuel tank.
● Do not use gasoline older than 30 days.
Add Fuel
Gasoline is extremely fl ammable and
its vapors can explode if ignited. Store
gasoline only in approved containers, in
well ventilated, unoccupied buildings, away
from sparks or fl ames. Spilled fuel could
ignite if it comes in contact with hot parts or
sparks from ignition. Never use gasoline as a
cleaning agent.
Ensure engine is cool.
1. Clean area around fuel cap.
2. Remove fuel cap. Fill to base of fi ller neck.
Do not overfi ll fuel tank. Leave room for fuel
to expand.
3. Reinstall fuel cap and tighten securely.
KohlerEngines.com
WARNING
Explosive Fuel can cause fi res
and severe burns.
Do not fi ll fuel tank while engine is
hot or running.
and should NOT be used; eff ects of
old, stale or contaminated fuel are not
warrantable.
WARNING
Explosive Fuel can cause fi res
and severe burns.
Do not fi ll fuel tank while engine is
hot or running.
14 590 48 Rev. A