Kohler Command Pro EFI ECH940 Benutzerhandbuch - Seite 7

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Motor Kohler Command Pro EFI ECH940 herunter. Kohler Command Pro EFI ECH940 8 Seiten.
Auch für Kohler Command Pro EFI ECH940: Benutzerhandbuch (8 seiten)

Seite drucken

Kohler Command Pro EFI ECH940 Benutzerhandbuch

Electronic Fuel Injection (EFI) System

EFI is an electronically-controlled fuel

management system which is monitored by an

Electronic Control Unit (ECU). A Malfunction

Indicator Light (MIL) will illuminate if problems

or faults are detected. Servicing by a Kohler

authorized dealer is necessary.

Fuel System Components

High pressure components inside fuel pump

module are not serviceable. Engines are

equipped with a special EFI fuel ﬁ lter. See

Maintenance Schedule.

Fuse Replacement

These engines have three (3) blade type

automotive fuses. Engines equipped with a

high output charging system, will have one (1)

60-amp large blade type automotive fuse, in

addition to the three (3) blade type automotive

fuses. However, the 30-amp fuse is then non-

functional, as the 30-amp charging system

circuit has been disabled.

Replacement fuses must have same rating as

blown fuse. Use fuse chart below to determine

correct fuse.

Wire Color

2 Solid Red Wires

1 Red Wire with Black Stripe

1 Red Wire with White Stripe

2 Purple Wires

High Output Charging System adds

In separate wiring harness;

when OEM supplied, refer to

your equipment manual for

fuse detail.

Air Cleaner

NOTE: Operating engine with loose or

damaged air cleaner components

could cause premature wear and

failure. Replace all bent or damaged

components.

NOTE: Paper element cannot be blown out

with compressed air.

Low-Proﬁ le

Loosen knobs and remove air cleaner cover.

Precleaner:

1. Remove precleaner from paper element.

2. Replace or wash precleaner in warm water

with detergent. Rinse and allow to air dry.

3. Saturate precleaner with new engine oil;

squeeze out excess oil.

4. Reinstall precleaner over paper element.

Paper Element:

1. Remove paper element with precleaner.

2. Separate precleaner from element; service

precleaner and replace paper element.

62 590 18 Rev. D

3. Install new paper element on base; install

Reinstall air cleaner cover and secure with

knobs.

Heavy-Duty

1. Unhook retaining clips and remove end

2. Check and clean inlet screen (if equipped).

3. Pull air cleaner element out of housing and

4. Check all parts for wear, cracks, or damage,

5. Install new element(s).

6. Reinstall end cap(s) with dust ejector valve/

Ensure both ends of breather tube are properly

connected.

NOTE: When oil cooler is remote mounted in

Fuse Rating

10-amp Fuse

1. Clean ﬁ ns with a brush or compressed air.

2. Remove two screws securing oil cooler, and

10-amp Fuse

3. Reinstall oil cooler.

30-amp Fuse

Kohler

60-amp Fuse

Proper cooling is essential. To prevent over

heating, clean screens, cooling ﬁ ns, and

other external surfaces of engine. Inspect for

any debris visible through ﬂ ywheel cooling

holes (if equipped) and clean as necessary.

Avoid spraying water at wiring harness or

any electrical components. See Maintenance

Schedule.

We recommend that you use a Kohler

authorized dealer for all maintenance, service,

and engine parts. To ﬁ nd a Kohler authorized

dealer visit KohlerEngines.com or call 1-800-

544-2444 (U.S. and Canada).

KohlerEngines.com

precleaner over paper element.

cap(s).

replace. Check condition of inner element;

replace when dirty.

and that ejector area is clean.

screen down; secure with retaining clips.

Breather Tube

Oil Cooler

application and supplied by OEM, refer

to your equipment manual for cleaning

detail.

tilt to clean back side.

Air Cooling

Hot Parts can cause severe

burns.

Do not touch engine while

operating or just after stopping.

Never operate engine with heat shields or

guards removed.

Repairs/Service Parts

WARNING