Dexford PCWS 4600 Betriebsanleitung - Seite 4

Blättern Sie online oder laden Sie pdf Betriebsanleitung für Wetterstation Dexford PCWS 4600 herunter. Dexford PCWS 4600 4 Seiten. Weather station with radio controlled projection clock

Seite drucken

PCWS 4600

Weather Station with Radio Controlled

Projection Clock

AAA 1,5 V

Thermo-sensor

AAA 1,5 V

ENGLISH

Operating Instructions

Please read and observe the following information and keep the

operating manual nearby for future reference!

WARNING!

Safety information

 Only use batteries of the same type!

 Always treat batteries with due care and attention and only use

batteries as described.

 Never use standard and rechargeable batteries together. Never use

rechargeable batteries or standard batteries with different capacities or

charge statuses together. Never use standard or rechargeable batteries

which are damaged.

 Risk of suffocation through small objects, packaging and protective foil!

 Keep children away from the product and its packaging!

 Risks to health and the environment from batteries!

 Never open, damage or swallow batteries or allow them to pollute the

environment. They could contain toxic and ecologically harmful heavy

metals.

ATTENTION!

 Prevent exposure to environmental influences, e.g. smoke, dust,

vibration, chemicals, moisture, heat and direct sunlight.

 Only allow repairs to be completed by qualified personnel.

PACKAGE CONTENTS

1 Weather station , 1 Thermo-sensor, Operating manual

OPERATING ELEMENTS

1 PROJECTION

2 SNOOZE / LIGHT

3 PROJECT

4 MAX / MIN

5 PRESSURE

6 MODE (Press to switch between alarm time 1 / 2 and current time

7 + / °C / °F (Press to switch between °C or °F)

8 - / RCC (Press to switch between time zone +1, +2 and -1)

9 CHANNEL (Press or slide to switch between CH 1, 2 and 3)

10 Battery compartment

11 A/C JACK IN (Optional, Power Adapter not included)

12 Hang hole

13 TX

14 Reset

During initial installation, the unit may take up to an hour or more to

acclimatise to current conditions. It is recommended to put the main

unit in the room where it will be used at least 1 hour prior to initial

installation.

STARTING UP

 After inserting the batteries (First Thermo-sensor / Secondly Main unit),

the main unit will connect with the Thermo-sensor.

 This process takes approx. 3 minutes. Then the display shows the

outdoor temperature. In case of failure of reception, please press and

hold "CHANNEL" for approx. 2 sec. to receive again.

 The weather station is capable of receiving up to 3 different channels.

Select the channel number (1, 2, or 3) by sliding the (9) switch.

The weather station will scan the 3 channels automatically.

 Select the channel number (1, 2, or 3) by pressing the "CHANNEL"

on weather station.

 The automatic reception of the DCF radio signal (DCF77, Time signal

frequency 77,5 kHz) starts after 3 minutes of outdoor RF reception.

 During this DCF reception process, the flashing symbol ( ) appears in

the time display area. This process can take up to 7 minutes.

 In case of failure of reception, pleases press "- / RCC" aprox. 3 sec. to

receive again or stop anytime.

 ATTENTION: During the reception process no other setting are possible!

 Once radio signal reception is successful, the display shows the symbol

"radio tower" permanently. This clock will automatically synchronize with

the radio control towers at the following time: 02:03, 03:03, 04:03, 05:03.

 Please observe a minimal distance of 2.5m to sources of interference

such as televisions or computer screens.

The radio signal (DCF) covers a distance of up to 1500km to Frank-

furt/Main. If no RCC automatic time reception is possible, try again

later time, or follow the steps below to set the time manually.

MANUAL SET-UP

(The clock automatically changes from set-up mode to time display mode if

no key is pressed for approx. 30 seconds.)

 Press and hold "PRESSURE" for approx. 3 sec. until a beep sound is

heard.

 Use "+ / °C / °F" and "- / RCC" to toggle between atmospheric pressure

units of Pascal (hPa) to inch of mercury (inHg)

 Press "PRESSURE" to confirm.

 Use "+ / °C / °F" and "- / RCC" to toggle between absolute / relative

atmospheric pressure

 Press "PRESSURE" to confirm.

 Use "+ / °C / °F" and "- / RCC" to set sea level closest to your location

 Press "PRESSURE" to confirm.

 Use "+ / °C / °F" and "- / RCC" to set current weather situation for your

location (See WEATHER FORECAST)

 Press "PRESSURE" to confirm and exit.

 While time is showing, press and hold "MODE" for approx. 3 sec. until

display is flashing.

 Use "+ / °C / °F" and "- / RCC" to change the language

(EN=English, GE=German, IT=Italian, FR=French, NE=Dutch,

ES=Spanish, DA=Danish)

 Press "MODE" to confirm.

 Use "+ / °C / °F" and "- / RCC" to set hour

 Press "MODE" to confirm.

 Use "+ / °C / °F" and "- / RCC" to set minute

 Press "MODE" to confirm.

 Use "+ / °C / °F" and "- / RCC" to set year

 Press "MODE" to confirm.

 Use "+ / °C / °F" and "- / RCC" to set month

 Press "MODE" to confirm.

 Use "+ / °C / °F" and "- / RCC" to set date

 Press "MODE" to confirm.

 Use "+ / °C / °F" and "- / RCC" to change between AM/PM and

24-hour clock

 Press "SMODE" to confirm.

 Press "MODE" to confirm and exit. The display stops flashing.

To see alarm time

 Press "MODE" to show alarm time A1

 Press "MODE" again to show alarm time A2

 Press "MODE" again to show normal time

Alarm set-up

 Press "MODE" to show alarm time A1

 Press and hold key "MODE" for approx. 3 sec. untill A1 flashes

 Use "+ / °C / °F" and "- / RCC" to set hour

 Press "MODE" to confirm.

 Use "+ / °C / °F" and "- / RCC" to set minute

 Press "MODE" to confirm.

 The same setting as for A2.

Alarm on/off

 Press "MODE", Alarm A1 is showing.

 Press "+ / °C / °F", A1 is activated ( )

 Press again "+ / °C / °F", A1 is disactivated

 The same setting as for A2.

The alarm will sound for 2 minutes. Press any key to stop it.

Snooze function

 Press the key "SNOOZE/LIGHT", while the alarm sounds, to activate

the snooze function. If the snooze function is activated, Snooze alarm

symbol is showing. The alarm repeat after 5 minutes. The snooze

function can be stopped by pressing any key.

Projecting the current time

This clock is equipped with night time projection. The time can be projected

onto a flat surface in a very dark room.

 Press "SNOOZE / LIGHT" to activate the time projection.

The current time will be projected for approximately 9 seconds.

 Turn the bottom knob clockwise or counterclockwise to adjust focus.

 Press "PROJECT" to change projection display 180°

WEATHER FORECAST

Sunny Slightly Cloudy Cloudy

Rainy

Max./ Min. for the indoor/outdoor temperature and humidity

 Press "MAX / MIN" for displaying indoor/outdoor max./min. of

temperature and humidity

 Press "MAX / MIN" for more than approx. 5 seconds to clear up the

max./min.

Temperature trend

increasing trend,

no change,

decreasing trend.

Feature

Value

PCWS 4600

W x H x D

163 x 110 x 40 mm

Weight

approx. 227 g (without battery)

Signal frequency

433 MHz

Power

2 x 1,5V AAA, not included

Temperature range

0 ~ +50 °C

Humidity range

20 ~ 95 %

External sensors, max. 30 meters in open area

W x H x D

63 x 63 x 20 mm

Weight

approx. 41 g (without battery)

Power

2 x 1,5V AAA, not included

Temperature range

-20 ~ +50 °C

Humidity range

20 ~ 95 %

To use for indoor and outdoor

Service hotline

In the case of technical problems, contact our Service hotline. Switzerland:

Tel. 0900 00 1675 (national charges, Swisscom at time of going to print:

CHF 2.60/min). In the case of claims under the terms of guarantee, contact

your sales outlet.

Maintenance

Clean the surface of the housing with a soft, fluff-free cloth. Do not use any

cleaning agents or solvents.

Guarantee

Dexford equipment is produced and tested according to the latest produc-

tion methods. The implementation of carefully chosen materials and highly

developed technologies ensure trouble-free functioning and a long service

life. The terms of guarantee do not apply to the batteries or power packs

used in the products. The period of guarantee is 24 months from the date

of purchase. All deficiencies related to material or manufacturing errors

within the period of guarantee will be redressed free of charge. Rights to

claims under the terms of guarantee are annulled following tampering by

the purchaser or third parties. Damage caused as the result of improper

handling or operation, normal wear and tear, incorrect positioning or

storage, improper connection or installation or Acts of God and other

external influences are excluded from the terms of guarantee. In the case

of complaints, we reserve the right to repair defective parts, replace them

or replace the entire device. Replaced parts or devices become our pro-

perty. Rights to compensation in the case of damage are excluded where

there is no evidence of intent or gross negligence by the manufacturer. If

your device does show signs of a defect within the period of guarantee,

please contact the sales outlet where you purchased the Dexford device,

producing the purchase receipt as evidence. All claims under the terms

of guarantee in accordance with this agreement can only be asserted at

the sales outlet. No claims under the terms of guarantee can be asserted

Cloudburst

after a period of two years from the date of purchase and hand-over of the

product.

Disposal

In order to dispose of your device, take it to a collection point

provided by your local public waste authorities (e.g. recycling

centre). According to the laws on the disposal of electronic and

electrical devices, owners are obliged to dispose of old electronic

and electrical devices in a separate waste container. The adjacent

symbol indicates that the device must not be disposed of in normal

domestic waste!

You are legally obliged to dispose of power packs and batteries

at the point of sale or in the corresponding containers provided at

collection points by local public waste authorities. Disposal is free of

charge. The symbols indicate that the batteries must not be disposed of in

normal domestic waste and that they must be brought to collection points

provided by local public waste authorities. Packaging materials must be

disposed of according to local regulations.

Declaration of Conformity

This device fulfils the requirements stipulated in the Directive

1999/5/EC on radio equipment and telecommunications terminal

equipment and the mutual recognition of their conformity. Conformi-

ty with the above mentioned directive is confirmed by the CE mark on the

device. To view the complete Declaration of Conformity, please refer to the

free download available on our web site www.dexford.com.