Coyote C1CH36 Handbuch für Gebrauch und Pflege - Seite 13
Blättern Sie online oder laden Sie pdf Handbuch für Gebrauch und Pflege für Grill Coyote C1CH36 herunter. Coyote C1CH36 17 Seiten. Stainless steel charcoal grill
Seite drucken
Out) to remove the spots.
a. Each of these polishing agents take about 30 seconds to work and then you simply wipe off the
product (if needed use a soft Scotch‐Brite pad to remove any tough spots.) If you used
Barkeepers Friend, then you do not need to do anything further. If you used Instant Rust Out
(or another cleaning agent), you would want to wipe it down with fresh water and dry it off
again with a clean towel and then coat the steel with a layer of WD‐40 or another Stainless
Polishing solution, which will act as a surface protectant for the steel.
i. IMPORTANT: Be sure not to have your grill on when using any flammable product, such
Environmental Factors that can affect your Grill
Mother Nature is a wonderful thing but unfortunately she can be tough on outdoor appliances. There are
several usual causes for surface discoloration and corrosion on your stainless steel outdoor equipment:
1) Mortar (which contains lime) from the island assembly process, has rested on the unit for a pro‐longed
period of time and the unit was not cleaned quickly
2) Pool chemicals were splashed onto the grill (chlorine and acid will cause very quick problems) and the unit
was not cleaned off quickly
3) Hard water from sprinklers (chlorine in the water) was allowed to sit on the unit
4) Salt from the ocean air/water was allowed to rest upon the grill for a prolonged period of time before being
cleaned (beach owners must be diligent in maintaining their outdoor stainless equipment)
5) Dust, or rust, from other metals found it ways onto the grill and was left on for an extended period of time.
6) Organic matters (such as certain types of food) might have gotten onto the surface of the grill and it was
then covered. With high humidity and low oxygen, corrosion will start to take place.
7) Sprays and cleaning solutions containing alkaline, lime, acid, salt might have been left on the grill surface
un‐dried.
8) No stainless steel polish was ever used after one of the above mentioned acts took place.
Ways to Avoid Rust on your Grill:
1) Always purchase a Coyote Grill cover for your unit. This will ensure that your cover is correct fit and
breathable, while providing the protection needed to keep all other contaminants off of the surface.
2) When installing the unit, make sure to keep the unit covered when any masonry work is being performed. If
any mortar or dust does come into contact with the stainless, make sure to wipe it off as soon as possible
and use a stainless steel polish immediately afterwards.
3) Position your grill away from areas that can receive water splash from a pool or hot tub.
4) Do not store pool chemicals in your island or island cabinets.
How to Remove Scratches from your Stainless Steel:
If your situation is a little more serious and you have obtained scratches in your equipment, then you will need
to purchase a "stainless steel scratch kit." These kits are popular in retail stores but can be easier to obtain
online. A very popular one is called "Scratch‐B‐Gone." With these kits, you will not polish the unit until you are
done re‐scratching the entire product you are working on. With a scratch kit, the goal is to literally re‐scratch the
entire surface, so that the original grains are replaced by your new scratched‐in grains. With this practice, you
must be willing to do the entire surface as you will notice a start and stop point. Also, be careful to pay attention
to your rolled or finished edges as these scratch kits will ruin this finish. After you have used the kit, you will
want to follow it up with a good stainless polish (as mentioned prior) and then a dry towel for a final wipe down.
as WD‐40. These products are extremely flammable in their aerosol form.
11