AB Quality SD3000 PLUS Installationsanleitung Handbuch

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Controller AB Quality SD3000 PLUS herunter. AB Quality SD3000 PLUS 12 Seiten. Dc drive regulator

Seite drucken

Infrared Control (IR)

The area on the front panel labeled IR or IR Extender is the IR

Transmitter (IR-TX) port.

Using the Ultra-IR Adapter Kit (optional) enables the control of the source

device from the location of the display. Plug the HDMI cable into the IR

Adapter at the display end. Next plug the IR Adapter's HDMI connector

into the display. The IR Adapter has a port that accepts an optional IR

Receiver (IR-RX). When the IR-RX receives an IR signal from the source

devices remote control, it uses the HDMI cable's CEC line to send the

signal to the splitter. Plug the optional IR-TX into the IR port on the front

panel of the splitter. Point the end of the IR-TX at the source device.

The signal is transmitted through the IR-TX sending the IR signal to the

source device.

Note: As the Ultra IR-Adapter uses the CEC channel of the HDMI cable,

the CEC function cannot be used when using this device. Turn off CEC or

HDMI Link functionality in the source devices and displays.

The illustration below shows the optional Ultra-IR Adapter Kit controlling

the source device on a 1x4 splitter. The 1x8 splitter is setup in a similiar

manner. Note: Due to specific pin requirements, only use Accell Ultra-IR

transmitters or receivers.

Ultra-IR Adapter Kit: PN: B164B-001B

Includes IR-Adapter: 1 pc.

IR Transmitter (5 ft.): 1 pc.

Dual Frequency: 38KHZ-60KHZ

IR Receiver (5 ft.): 1 pc.

Ultra-IR Receiver (5 ft.)

Dual Frequency: 38KHZ-60KHZ

PN: B164B-002B

Ultra-IR Transmitter (5 ft.)

Dual Frequency: 38KHZ-60KHZ

PN: B164B-003B

Ultra-IR Receiver and

Transmitter Pin assignment

Troubleshooting

Q. One of the display does not show a picture or output audio.

A. Check the displays input setting to ensure it is set to receive a signal

from the connected HDMI port.

Q. One or more of the connected displays will not display a picture while

one or more of the displays do display a picture:

A1. Press the RESET button on the front of the splitter to reset it.

Alternatively turn off the power to the splitter, source and displays. Wait

60 seconds. Turn the source on. Turn the displays on.Turn the splitter on.

A2. The HDMI cables on the non-functonal display/s cannot support

their long length. Use only high-quality High Speed HDMI cables. Keep

the cable length as short as possible. Test by locating the non-working

display close to the splitter. Use a short HDMI cable to connect the

splitter to the TV. A working TV using a short HDMI cable indicates an

issue with the HDMI cable.

Q. Get the message "This protocol is not supported" or other error

message.

A. See answer A1 above and repeat the steps outlined.

Q. The splitter is not down sampling the video and some of the TV's are

not displaying a picture.

troubleshooting continued...

A1. Go into the TV's setup and configure the resolution to match all the

connected TV's. The TV's should share the same resolution.

A2. In the source devices menu options set the source device to output a

resolution that matches all the connected displays.

Q. My TV's resolution are not optimized.

A. The splitter will query the displays and provide the highest common

video resolution amongst them. Example: Using a 1080p source, if 3

of the displays support a maximum resolution of 1080p and 1 display

supports a maximim resolution of 720p, all 4 display will operate at a

resolution of 720p. If the 720p TV in the example is then turned off, the

other 3 displays can then operate in 1080p resolution. Press the RESET

button on the front panel of the splitter to refresh the configuration. The

three 1080p TV's will refresh (flicker) then each will display a 1080p

resolution picture.

ASSISTANCE: Questions regarding this product or its product

warranty, please check out our Web site at: www.accellcables.com.

Customer service can be reached by email at [email protected]

or phone at 510-438-9288, toll free 877-353-0772 (M-F 9am-5pm PST).

1-YEAR MANUFACTURERS WARRANTY

The Accell UltraAV Splitter is warranted for one year from date

of purchase to be free of defects in material and workmanship.

In the event of such defects, the Accell product will be repaired

without charge or replaced with a new one at our option, if

delivered to Accell Corporation prepaid, together with a copy

of the sales receipt indicating the proof of purchase date and

place of purchase. This warranty excludes defects due to normal

wear, abuse, shipping damage, or failure to use the product in

accordance with the instructions. ACCELL CORPORATION SHALL

NOT BE LIABLE FOR DAMAGES BASED UPON INCONVENIENCE,

LOSS OF USE OF THE PRODUCT, LOSS OF TIME, INTERRUPTED

OPERATION OR COMMERCIAL LOSS, OR ANY OTHER DAMAGES,

WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE. YOU

AGREE THAT ACCELL'S MAXIMUM LIABILITY ARISING FROM

ANY PRODUCT SOLD BY ACCELL SHALL NOT EXCEED THE PRICE

OF SUCH PRODUCT. SOME JURISDICTIONS DO NOT ALLOW

THE LIMITATION OF EXCLUSION OF LIABILITY FOR CERTAIN

DAMAGES, SO THE ABOVE MAY NOT APPLY TO YOU TO THE

EXTENT SUCH JURISDICTION'S LAW IS APPLICABLE TO THIS

AGREEMENT. This warranty gives you specific legal rights, and

you may have other rights that vary from state to state.

LIMITATION OF LIABILITY

IN NO EVENT SHALL ACCELL CORPORATION, ITS SUBSIDIARIES

OR AFFILIATES, OR THEIR RESPECTIVE PARTNERS, OFFICERS,

DIRECTORS, EMPLOYEES, SHAREHOLDERS, REPRESENTATIVES

OR AGENTS (COLLECTIVELY, "ACCELL") BE LIABLE FOR

DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE,

OR INDIRECT DAMAGES (INCLUDING BUT NOT LIMITED

TO, LOSS OF DATA, USE OR PROFITS), HOWEVER CAUSED,

WHETHER FOR BREACH OF CONTRACT, NEGLIGENCE, OR

OTHERWISE, AND WHETHER OR NOT ACCELL HAS BEEN

ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES. YOU

AGREE THAT ACCELL'S MAXIMUM LIABILITY ARISING FROM

ANY PRODUCT SOLD BY ACCELL SHALL NOT EXCEED THE PRICE

OF SUCH PRODUCT. SOME JURISDICTIONS DO NOT ALLOW

THE LIMITATION OF EXCLUSION OF LIABILITY FOR CERTAIN

DAMAGES, SO THE ABOVE MAY NOT APPLY TO YOU TO THE

EXTENT SUCH JURISDICTION'S LAW IS APPLICABLE TO THIS

AGREEMENT.

WARRANTY RETURNS PROCEDURE

Contact Customer Support to obtain a Return Authorization

(RMA) number. RMA numbers are valid for 30 days from the date

of issuance. We are unable to accept returns without an RMA

number. Returns without an RMA number clearly printed on the

outside of the package will be refused and returned unopened. All

returns must be shipped prepaid at the expense of the shipper.

Accell assumes no responsibility for any inaccuracies and liability

for direct, indirect, special, incidental, or consequential damages

as a result. Due to ongoing improvements, Accell reserves

the right to make changes to hardware, packaging and any

accompanying documentation without prior written notice.

are registered trademarks of Accell Corporation.