DEZIT CN 024 100 EIS W Handbuch - Seite 4

Blättern Sie online oder laden Sie pdf Handbuch für Elektrischer Heizer DEZIT CN 024 100 EIS W herunter. DEZIT CN 024 100 EIS W 16 Seiten. Electric panel heater

Seite drucken

"OFF" position, then you need to wait for 3 seconds and the function will

automatically go in "OFF" mode.

•

to enable this function again, the convector must be in "Off" mode, when

you press the

and "On/Off" button for three seconds the display will

show a blinking "OFF", and by pressing the

"ON" position, then you need to wait for 3 seconds and the function will

automatically go in "ON" mode.

"Temperature correction for the sensor" function

Due to the specifics of the temperature profile in some premises there may be

difference from the temperature shown on the display and the actually measured

temperature in the various locations of the heating appliance in the room.

•

See the temperature shown on the display of the appliance

•

Measure the temperature at a place where the temperature is "comfortable"

enough for you (usually at a height of 60 cm from the floor, in sitting

positon). If you find a difference within a range of ±4°С, you can set the

necessary correction in the convector's menu (It is important to note that

this function can be set only after the temperature has become the same all

around the room, and depending on the room type, the minimum required

time is 7 hours) by entering the temperature difference resulting between

the value on the display and the actually measured temperature.

Note: This function is used with the purpose of providing better

temperature comfort and energy saving for the user of the electric

convector in the room which it is in. A temperature difference greater than ±4 °C

from the measured temperature in a specific location in the room indicates that

the room where you use the convector in is not well insulated or the temperature

is not the same all around the room.

Example: a convector in a room on a stone floor – the convector displays 18°С

(the set temperature is 22°С), the actually measured temperature (feeling of

reached comfort temperature) is 22°С at a height of 60 cm from the floor - > in

this case the convector continues to overheat the room (this is a direct energy

loss, but the convector cannot reach the set temperature because it measures the

temperature at a low height close to the floor) and it will never switch off. In this

case a temperature correction of +4°С needs to be applied to the sensor, thus the

convector will display 22°С and it will start switching off, and eventually it will

maintain the set temperature of 22°С).

The normal status of the function is 0°C by default

•

to change this value, the convector must be in "Off" mode, when you press

the

and "On/Off" buttons for three seconds the display will show a

blinking "0oc". You can press either the

to „4°С" range, then you need to wait for 3 seconds and the function will be

automatically stored.

•

to check what correction has been set, the convector must be in "Off"

mode, when you press the

will see the set temperature blinking on the display. By pressing the

buttons you can set a new value within a range from „-4°С" to „4°С".

Note: After activating the Return to Factory Settings function a new

temperature correction has to be entered, the value by default is 0°С)

Adaptive start

•

Adaptive start control is a function which predicts and initiates the optimal

start of heating up in order to reach the set temperature in the desired time.

•

this function is enabled by default

•

to change the value, the convector must be in "Off" mode, when you press

the „ " and "Timer" buttons for three seconds the display will show a

blinking "A_On". You need to press the „ " button to reach „AOFF"; then you

need to wait for 3 seconds and the function will be automatically stored.

•

To return to „ON" status – the convector must be in "Off" mode; when you

press the

and "Timer" buttons for three seconds the display will show a

blinking "AOFF"; you need to press the

need to wait for 3 seconds and the function will be automatically stored.

This function can be set according to your needs. The appliance operates

for 17 hours following the set "comfort" temperature until it reaches a stable

status – this is the reference comfort temperature. Also, a temperature lower

than the comfort one, with a difference from 4°C ± 1°С, has to be set for a

period of minimum 7 hours. When the adaptive operation is enabled, leave

the electronic thermoregulator of the appliance to operate for 4 cycles (4 х 24

hours) of comfort cycles (17 hours) and lowered temperature (7 hours). Upon

completion of the last period of low temperature, the comfort temperature

should be reached within ± 30 minutes deviation from the set time, with a

maximum difference of ± 1°C from the reference comfort temperature.

"Protection from children"

You can lock the buttons by continuously pressing the arrows

Operation and Storage Manual of Panel Heater

button you will reach the

button to reach the „-4°С"

and "On/Off" buttons for three seconds you

button to reach „A_On", then you

and "Timer"

buttons simultaneously, in order to prevent any changes to the settings.

Repeat the same action to unlock the buttons.

Note: If you press any of the buttons when the keypad is locked, the display

will show „LOC_"

Settings in „Weekly programmer 24/7"

Entering settings mode of "Weekly programmer" is possible only after

the time and the day of the week have already been set in the appliance..

To enter and exit the settings mode you need to continuously press the

"Timer" button.

There are three parameters to be set – day of the week, time and temperature;

switching among the three parameters is done by shortly pressing the "Timer"

button in the following sequence: day, time, temperature. To store the settings,

press shortly the "Timer" button after you finish the temperature setting.

You can change the value of each parameter by using the

Conditions for settings storing

a. After a point has been stored, it cannot be changed any more until you exit the

current setting.

b. Upon storing the first set point of a specific day in the current setting, all

previously set points of the day are cleared.

c. Storing further points of a specific day is possible only for the hours remaining

until the end of the day, after the last stored point.

d. When you have stored a point in the last hour of the day – 23.5h, you cannot

store any more points for this day in the current setting, and the display will

show "FUL" and the number of the day.

e. If nothing is stored in the current setting for a specific day, it will keep the

existing stored points up to the current setting.

The purpose of the settings is to store the three parameters in the so called

"SET POINTS", where the temperature set for each set point is implemented

until the next one is reached.

Example: If you have stored the temperature to be 22°C at 7 h and you wish the

temperature to remain the same until 19 h (you plan the temperature to increase

to 23°C then), you do not need store every single hour until 19 h, and you only

need to store the temperature to be 23°C at 19 h. By default the temperature will

be 22°C during this period of time (7 – 19 h).

The procedure for storing each point is as follows:

Upon entering settings mode the display will show dAY1, with the numeral

blinking to indicate that this is the parameter to be set (in this case it is the day

of the week).

a. to select the desired day, use the

b. to go to time setting, shortly press the "Timer" button

c. use the

and

buttons to select the desired time (with a 0.5h interval) per point

d. to go to temperature setting, shortly press the "Timer" button

e. to select the desired temperature, use the

temperature range is from 10 to 30°С, and OFF status is possible as well.

To store the point, shortly press the "Timer" button; then you are automatically

transferred to the setting of the next point (the display again shows dAYX) and

you can proceed with paragraph а) for the next point.

g. When you have stored a point in the last hour of the day – 23.5h, you cannot

store any more points for this day in the current setting, and the display will

show "FUL_" and the number of the day.

ATTENTION: Points of a particular day may be stored only in

ascending order of their times.

Note: Before implementing paragraph f) the user can go back to paragraph

а) to correct the three parameters of a point by shortly pressing the ON/OFF

button, without storing the settings in the memory.

Adding more points in a particular day may be done at random, after you

have stored points for other days, however you need to observe the rule for

ascending order of their times in a day.

To exit the settings mode, press continuously the "Timer" button and wait for

30 seconds.

Upon leaving the settings you can review the stored points by using the

and

buttons.

and

buttons

and

buttons. The possible