AVS AFM625B Gebrauchsanweisung - Seite 2

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Racks & Ständer AVS AFM625B herunter. AVS AFM625B 2 Seiten. For lcd, plasma, and led displays

Seite drucken
Part 1B – Mounting to the Wall (Concrete) (continued)
Carefully remove the plastic covers from the mount as shown
1
(see Fig. 1).
Place the mount against the wall in the desired location with
2
the arrow on the mount pointing up. Make sure it is level.
While another person holds the
3
mount in place, mark four
locations for securing the mount
to the wall (see Fig. 4).
Set the mount aside and drill a
4
3/8" hole at each marked location.
Remove any excess dust from the
holes.
5
Insert a concrete anchor (C) into
each hole so that it is flush with
the concrete surface (see Fig. 5). A
hammer can be used to lightly tap
the anchors into place if
necessary.
6
Attach the mount to the wall with the arrow pointing up
using the lag bolts (A) and washers (B) provided (see Fig. 3).
Do not release the mount until all bolts are secure. Ensure
that the mount remains level.
Part 2 – Attaching the Mount Arms to the Display
IMPORTANT! Use extra care during this part of the installation
to avoid damaging your display.
NOTE: This mount comes with a variety of screw lengths and
diameters to accommodate different display models. Not all of
the hardware in the kit will be used. If you cannot find the
appropriate screw size in the kit provided, consult with the
manufacturer of your display or a professional installer.
Determine the correct length of screw to use by examining
1
the back of your display:
If the back of your display is flat and the mounting holes
A
are flush with the surface, use the shorter screws from the
hardware kit.
B
If the back of your display is curved or if additional space
is needed between the display and the mount, use the
longer screws.
Part 2 – Attaching the Mount Arms to the Display (continued)
Determine the correct diameter of screw to use by carefully
2
trying one of each size from the hardware kit. Do not force
any of the screws – if you feel resistance stop
immediately and try a smaller diameter screw.
Attach the mount arms to the back of your display using
3
Fig. 4
the screws identified in steps 1 and 2 (see Fig. 6):
A
If you are using the M8 screws you will need to use the
M8 Washers (I). If you are using smaller screws, you will
need to use the M6 washers (F).
If you are using the longer screws, you may also need to
B
use spacers (J).
Fig. 5
For displays with
flat backs.
Part 3 – Final Assembly
With the help of another person, carefully lift your display
1
and place it on the mount. Do not release the display
until the mount arms have
securely hooked onto the
mount.
Close the safety latch at the
2
bottom of each arm. Each
latch will automatically lock
when fully closed (see Fig. 7).
IMPORTANT! The latches must be closed and locked at
all times to prevent the display from being accidentally
knocked from the mount.
3
Re-attach the plastic covers removed in part 1.
Cables can be routed through the channels located on the
4
bottom of the mount. Make sure none of the cables can be
pinched during operation of the mount.
OPERATION AND ADJUSTMENT
1
To change the tilt angle of
your display, have one
person hold the display
firmly in place while
another person loosens
the tilt knob (see Fig. 8).
Once loosened, move your
display to the desired
position, and then
re-tighten the knob. Do
not release the display until the knob is fully tightened.
Swivel adjustments can be made by moving the display
2
For displays
to the desired position. Be careful that fingers or cables do
Fig. 6
with curved or
not get pinched when moving the mount.
recessed backs.
Level correction
3
adjustments can be made
by rotating the display in
the needed direction. If it
is too difficult to turn the
display or if the display
does not stay in position,
adjust the tension of the
two wing nuts located
behind the faceplate.
Adjust the two nuts evenly (see Fig. 9).
Fig. 7
Level correction nuts
IMPORTANT! Never fully loosen or remove the level
correction nuts.
Fig. 8
Fig. 9
3202618-151116