CPI TALOS T700 Handbuch installieren - Seite 2
Blättern Sie online oder laden Sie pdf Handbuch installieren für Verkaufsautomaten CPI TALOS T700 herunter. CPI TALOS T700 2 Seiten. Bill validator
Seite drucken
installation
Before installation, remove the Talos bill validator from the packaging
and inspect for any physical damage. If damaged, contact customer
service at 1-800-345-8215.
1. Turn off power to the vending machine.
2. Mount the Talos bill validator on the mounting studs, through the
opening in the front of the vendor and secure using the included
hardware.
3. Connect the Talos bill validator to the MDB harness. Apply gentle
pressure to connect; the pins will bend if forced.
4. Turn on power to the vending machine.
5. Check the LEDs on the front of Talos. The LEDs should be
flashing. In some cases, the machine door must be closed first.
6. Once the LEDs are flashing, test the validator with a $1 bill.
a. Insert $1 and confirm that it stacks and credit is given.
b. Repeat this process for any other enabled bills.
7. When your test is complete, remove the test bills from the bill
magazine.
The installation is now complete. Refer to the other sections of this
guide to configure the device, if necessary.
enabling bills and vend coupons
Follow this process to enable or disable bills or vend coupons:
1. Remove the bill magazine, then use a pencil or a screwdriver to
press the button to enter configuration mode:
Press this button
2. Reattach the bill magazine.
3. Insert the bill or vend coupon.
4. The bezel LEDs flash when the bill or vend coupon is returned.
5. Count the flashes to determine the outcome using the chart on
the next section.
Talos_Install_Guide_5.24.19.indd 2
enabling bills and vend coupons - Continued
Number of Flashes
Meaning
The bill or vend coupon has been
10
enabled successfully
The bill validator was unable to read the
7
bill or vend coupon. Try again.
The bill or vend coupon has been
3
disabled
Configuration coupons
The unit is pre-configured with the following options enabled:
– Accept $1 bills
– Four way accept
Use the included coupon to change the settings:
1. Carefully cut out the coupon
2. Fill out each line using an HB or #2 pencil
Section
Changes
Options
1 - Face up in one direction (green seal
first)
Bill Way
1
Accepted
2 - Face up in either direction
4 - Face up or down in either direction
Bills
2
On or off to enable or disable a bill
Enabled
Recycled
Can be left blank, but is required for the
3
Bill
recycler
Accept
4
Requires a Recycler
Inhibit
Configuration Coupons - Continued
Section
Changes
Options
5
Acceptance
Mode 0: Factory default. No
Mode
acceptance modes active.
Mode 1*: If fraud is detected the
validator enters an out-of-service
time-out, the stacker plate extends
into the bill magazine and the bezel
LEDs flash. If any sensors are
blocked, the time-out persists until
the blockage is cleared.
Mode 2*: All the features of Mode 1,
plus the stacker plate extends into the
bill magazine when idle.
Mode 3*: All the features of Mode 2,
but more aggressive. It may increase
jams and service calls. Mode 3 is
recommended for temporary use
only.
*Requires power
Insert the configuration coupon and verify the settings were accepted
by counting the bezel flashes
Flashes
Meaning
Configuration coupon accepted and unit
10
successfully programmed.
Coupon rejected. Number of flashes corresponds
1 - 5
to the coupon section that was improperly filled
out. Try again.
Coupon not read. Confirm the coupon is
7
correct and try again.
5/24/2019 9:54:44 AM