Dell D90D7 Installationshandbuch - Seite 22

Blättern Sie online oder laden Sie pdf Installationshandbuch für Server Dell D90D7 herunter. Dell D90D7 24 Seiten. D class cloud clients
Auch für Dell D90D7: Schnellstart-Handbuch (6 seiten), Schnellstart-Handbuch (8 seiten), Schnellstart-Handbuch (6 seiten), Schnellstart-Handbuch (6 seiten), Schnellstart-Handbuch (8 seiten), Schnellstart-Handbuch (10 seiten)

Seite drucken

Chapter 5

Step 4: Use the Configured USB Key to Install Firmware on Each Thin Client

In this step, you will boot each target device you want to convert from the configured

USB key so that the USB key will push the contents from the USB key onto the target

device. NOTE: BIOS selection, movement, and exit instructions are displayed in the

BIOS window.

Depending on your device, use the following guidelines to configure it to boot from the

configured USB key:

For D90D7 and D90DW thin clients:

•

For X90m7 and X90mw mobile thin clients:

•

For Z90D7, Z90S7 Z90DW, and Z90SW thin clients:

•

TIP: When booting a target device from the configured USB key (containing the

contents to be pushed to a target device), you will be prompted to continue with the

push process (to continue, type y and press Enter). Once the push process is complete,

you will be prompted to reboot (to reboot, press Enter and remove the USB key).

CAUTION: DO NOT interrupt the installation/conversion process. All process

requirements are done automatically.

TIP: You can use the configured USB key to push the firmware onto as many target

devices as you want (repeat "Step 4: Use the Configured USB Key to Install Firmware on

Each Thin Client").

Step 5: Verifying Thin Client Operation

After the thin client reboots, you can verify your general client information. For

example, the Client Information dialog box (D class), or the System Information dialog

box (X class and Z class) information is correct (that the new Flash is correctly

recognized by the system). After verification, the thin client is ready for operation and

setup by an administrator.

TIP: Administrator and other documentation for your thin client model are available at:

http://www.wyse.com/manuals.

CAUTION: For X90m7 and X90mw mobile thin clients, you can change the BIOS Setup

Utility back to its original state.

You must change the BIOS Setup Utility (you do not need to restore your settings

later, as the new firmware will restore default settings automatically after you

start your thin client): Be sure the client is shut down and disconnected from any

network. Attach the configured USB key to the thin client. During boot, press and

hold the Delete key. Enter the password Fireport (this is case sensitive) and press

Enter. Select the Advanced tab. Using the down arrow key, select the Boot from

USB option and press Enter. Select the Enabled option and press Enter. Press the

F10 key, and then press y to save the BIOS settings and reboot. Follow the

process prompts.

You must change the BIOS Setup Utility (you can restore your settings later in

"Step 5: Verifying Thin Client Operation"): Be sure the client is shut down and

disconnected from any network. Attach the configured USB key to the mobile

client. During boot, press and hold the F2 key. Enter the password Fireport (this

is case sensitive) and press Enter. Select the Boot option and press Enter. Select

the Legacy option and press Enter. Select the Normal Boot Menu option and

press Enter. Select the option displaying your USB key vendor name and move it

to the 1 position by using the + key. Save the BIOS settings and reboot. Follow the

process prompts.

You must use the one-time boot menu (the one-time boot menu will not modify

your default BIOS configurations): Be sure the client is shut down and

disconnected from any network. Attach the configured USB key to the thin client.

During boot, press and hold the P key. Select the USB HDD option (displaying

your USB key vendor name) and press Enter. Follow the process prompts.