Avue G40 Benutzerhandbuch - Seite 11
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Sicherheitskamera Avue G40 herunter. Avue G40 14 Seiten. Middle speed dome camera series
Seite drucken6.OSD - Zones and Privacy Mask
Zones
Z O NE S
You can define the zones in the whole PT range up to
8 zones. When the display setting "Zone Label" is
ZONE NUMBER
1
activated, its label will be displayed on the screen.
SET LEFT LIMIT
The defined ranges of the zones should not be
SET RIGHT LIMIT
overlapping.
CLEAR ZONE
EDIT ZONE LABEL
ZONE NUMBER: Supports up to 8 zones.
BACK
EXIT
SET LEFT LIMIT: Left boarder of the current zone.
SET RIGHT LIMIT: Right boarder of the current zone.
CLEAR ZONE: Delet the current zone.
EDIT ZONE LABEL : Changes the label (name) of the
current zone.
Privacy Mask (Window Blanking)
WINDOW BL AN KI N G
Privacy Mask is used to protect the privacy area that
WINDOW NUMBER
01
should not be displayed once the camera is pointed
EDIT WINDOW
on it, such as lavatory areas or the operation desk of
ENABLE WINDOW
OFF
an ATM machine. This might be mandatory required
CLEAR WINDOW
by local law regulations. The Speed Dome supports
BACK
up to 24 private masks (depending on the installed
EXIT
camera module; please contact your local sales
representative for more information).
Hitachi camera modules: 8 masking areas
Sony Camera modules: up to 24 masking areas
(except the 45 series provides only 8)
LG,CNB Camera modules: no masking function
WINDOW NUMBER: Mask number.
EDIT WINDOW: Edit position of the mask using the
keyboard's joystick. Presse IRIS-OPEN to save.
ENABLE WINDOW: Shows the mask on the screen.
CLEAR WINDOW: Deletes the mask.
17
Some products may not be available in your country, please contact our distributor for more details
7.PROTOCOL SETTING
Protocol Setting
This procedure is needed if a connection of the
telemetric control with the keyboard device is
desired. You need to setup the dome address and
protocol settings.
The speed dome support multiple communication
protocols. The settings can be changed by
rearranging the DIP-Switches on the rear side of
the connector board as illustrated.
Please use the following table for detailed
information.
SW 1:
Represents the dome's address in binary form.
Please refer to the list on the next pages for
reference.
SW 2:
Used for protocol settting and baud rate.
DIP 1 to 6 : Protocol settings
DIP 7 and 8:Baud rate settings
Baud rate
DIP 7 DIP8
2400 bps
0
0
4800 bps
1
0
9600 bps
0
1
19200 bps
1
1
Some products may not be available in your country, please contact our distributor for more details
Protocol / DIP
1 2 3 4 5 6
B02
0 0 1 1 0 0
DIAMOND
1 0 0 1 0 0
HUNDA
1 0 1 1 0 0
KALATEL
0 1 0 1 0 0
LILIN
1 1 0 1 0 0
MOLYNX
0 0 1 0 0 0
PANASONIC
1 1 1 0 0 0
PELCO (D/P)
1 0 0 0 0 0
PHILIPS
0 0 0 0 0 1
SAE
0 1 0 0 0 0
SAMSUNG
0 0 0 1 0 0
SANTACHI
0 1 1 0 0 0
UNIVISION
0 1 0 0 0 1
VCL
1 1 0 0 0 0
VICON
1 0 1 0 0 0
AD
0 0 1 1 0 0