Dell Daily Deal E1909W Service-Handbuch - Seite 11

Blättern Sie online oder laden Sie pdf Service-Handbuch für Monitor Dell Daily Deal E1909W herunter. Dell Daily Deal E1909W 50 Seiten. Lcd monitor
Auch für Dell Daily Deal E1909W: Einrichten (2 seiten), Benutzerhandbuch (31 seiten)

Seite drucken

D854&D855 are used to rectify the inducted current. C862 are used to store energy when current is

reversed. The parts including C863 is used to smooth the current waves that are from D854&D855, and then

24V voltage is supplied.

D856&D857 are used to rectify the inducted current. C873 are used to store energy when current is

reversed. The parts including C856, C857, C858 ,C876 and L854 are used to smooth the current waves that

are from D856&D857, and then 5V voltage is supplied.

24V and 5V supply voltage feed back to PWM controller U850 via R871, R872, R868 and

I850,I851.R860,C859 and C871 used to control respond time.

LD7552B are implemented an OVP function on Vcc.Whenever the Vcc voltage is higher than the OVP

threshold voltage,the output gate drive circuit will be shutdown simultaneously thus to stop the switching of

the power MOSFET until the next on.

2.3 I/F Board Circuit (see the Attachment 2- Schematic)

2.3.1 RGB CAPTURE

- Signal RED,GREEN,BLUE input through CN102 #1,#2,#3, Stop DC via C113, C114 and C115, and

then enter into U105 (TSUM5PEHJ-LF-2) analog input PIN #28,#25,#23, and then

TSUM5PEHJ-LF-2 deals with signal internally. D103, D104, D105 are ESD protector to prevent

U105 from ESD.

- Signal DDC_SCL (series clock) inputs via CN102#15, and then passes through ZD106 for ESD

protection, goes into EDID EEPROM IC U103 #6.

- Signal DDC_SDA (series data) inputs via CN102#12, and then passes through ZD103 for ESD

protection, goes into EDID EEPROM IC U103 #5.

- Signal TTL vertical sync. (Vsync) inputs via CN102 #14, and then clamped by ZD105 Zener, passes

through R134, and then goes into IC U105 (TSUM5PEHJ-LF-2) #33.

- Signal TTL horizontal sync. (Hsync) inputs via CN101 #13, and then clamped by ZD102 Zener,

passes through R133, and then goes into IC U105 (TSUM5PEHJ-LF-2) #32.

- CN101#5 is defined as cable detect pin, this detector realize via R121 and U104#36, and D102 is

ESD protector.

- U103 +5V is supplied by PC via CN102#9 with ZD102 for ESD protection, or supplied by Monitor

self via D106

- U103 is an EEPROM IC which is memory and EDID data saved in it.

2.3.2 DVI CAPTURE

- Differential Signal input RX0+,RX0-,RX1+,RX1-,RX2+,RX2-,RXC+,RXC- through CN201

#18,#17,#10,#9,#2,#1,#23,#24 via R206,R205,R204,R203,R202,R201,R207,R208 enter into U105

(TSUM5PEHJ-LF-2) Digital input terminal #16,#15,#13,#12,#10,#9,#18,#19, and then

TSUM5PEHJ-LF-2 deals with signal internally. D206, D207, D204, D205, D202, D203, D208,

D209 are ESD protector to prevent U105 from ESD

- Signal DDC_SCL (series clock) inputs via CN201#6, and then passes through ZD204 Zener for ESD

protection, via R209, goes into EDID EEPROM IC U201 #6.

- Signal DDC_SDA (series data) inputs via CN201#7, and then passes through ZD203 Zener for

ESD protection, via R210, goes into EDID EEPROM IC U201 #5.

- CN201#15 is defined as cable detect pin, this detector realize passes through R216 ,go into U105#49,

and D210 is ESD protector.

- U201 +5V is supplied by PC via CN201#14 through D201, or supplied by Monitor self via D201.

- U201 is an EEPROM IC which is memory and DVI input EDID data saved in it.

2.3.3 Buttons Control

- Button "Power" on front bezel connects to U105 (TSUM5PEHJ-LF-2) #4 through CN104 #8, U105

#4 is defined as power on/off.

- Button "+" on front bezel connects to U105 (TSUM5PEHJ-LF-2) #120 through CN104 #2,

U105#120 Voltage is defined as "Plus".

- Button "-" on front bezel connects to U105 (TSUM5PEHJ-LF-2) #121 through CN104 #3, U105

#121 Voltage is defined as "Minus".

Service Manual