EarthMinded RBK-0001 Benutzerhandbuch

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Water System EarthMinded RBK-0001 herunter. EarthMinded RBK-0001 2 Seiten. Do-it-yourself rain barrel diverter and parts kit

Seite drucken

Do-It-Yourself Rain Barrel Diverter and Parts Kit

User Guide RBK-0001 V.2

EarthMinded has assembled all the parts needed to make a rain barrel using a recycled barrel or plastic waste barrel

(barrel not included). Using this kit, anyone who can use a drill can make and install a rain barrel in minutes!

Please read all instructions and warnings before installation, and retain this Booklet for future reference

General description

Rain barrels have been used for hundreds of years to harvest and

store rainwater for use with plants, gardens, and other outdoor

chores.

EarthMinded's DIY Rain Barrel Kit can be used to make a state-

of-the art sealed rainwater collection system when used with

a barrel or container you supply. Our patent pending FlexiFit™

diverter installs easily by drilling a single hole into any standard

2" x 3" or 3" x 4" rectangular downspout*. The diverter sends

rainwater into the barrel. Once the barrel is full, the diverter will

automatically pass excess water through the downspout.

Open Top Container

human or animal consumption

Parts list

3 Pc. Hole Saw Set

FRN-015

Sticker

FLB-204

Do Not

Drink

Water

Threaded

Rubber Seal

Barrel Not

FRN-067

Included

Spigot

FRN-061

Threaded

Rubber Seal

Drain Assembly

FRN-067

FRN-080

Selecting a container

EarthMinded supplies only the parts and fittings to be added to a

barrel you supply. Therefore, we take no responsibility for losses,

damages, or injury caused by failure of the barrel, or improper

installation of the parts. Follow these instructions carefully for

successful results.

This kit will work on both sealed barrels and open top barrels with lids.

Open top barrels are easier to clean, and provide quick access to the

water using a bucket or watering can, but present a safety concern for

children; the lid must always be latched and locked.

Water weighs 8.3 lbs. per gallon. Be sure to select a sturdy container that

can support the weight when full. 55 gallons of water weighs 465 lbs.

WARNING

Stored rainwater is not

suitable for human or

animal consumption

Plastic Waste Barrel (Open Top)

Wood Barrel

The FlexiFit diverter helps discourage mosquitoes, pests, and

algae-causing sunlight from entering the barrel. The diverter is

easy to remove from the downspout and the kit includes a winter

hole cover.

The FlexiFit diverter offers many advantages over conventional

top fill rain barrels that commonly flood with heavy rain, require

permanent modifications to your downspout, and use unsightly

overflow hoses.

*Water capture percentage is reduced with 3"x 4" downspouts

Round downspout diverter available as an accessory

Spigot

2. Drain or hose

attachment

3. Fill hose

4. FlexiFit diverter

5. Winter hole cover

Some areas prohibit the

use of rain barrels. Please

check local regulations

before installing.

WARNING

Sealed Barrel

Stored rainwater is not for

Tools needed

1. Safety Glasses

Fill Hose

FRN-054

2. Safety Gloves

FlexiFit Diverter

FRN-008

Fill Hose Seal

3. Drill

FRN-043

Screws

4. Measuring

Winter Hole

Tape or Ruler

Cover

FRN-009

5. Pencil

6. Phillips

Instructions

Screwdriver

7. Level

Select a sturdy water tight container:

a. A heavy duty or commercial grade plastic waste barrel with

latching lid.

b. A traditional wood barrel can make an attractive and natural

looking rain barrel. Make sure it is in good condition, clean and

water tight.

c. If using a recycled barrel, use only FDA approved food grade

barrels. Make sure the barrel is clean and has not been used to

contain toxic or hazardous substances.

The container selected should be sealed, or have a latching lid to help

prevent mosquitoes, animals, and children from entering the barrel.

This kit is not recommended for use with metal drums or barrels.

Recycled Plastic Barrel (Sealed)

Select a location for your rain barrel

Before assembling the parts to the barrel we recommend that you select

and prepare the location where the barrel will be used. This will help you

locate the fittings on the barrel in the most convenient location.

•

Choose a downspout that is near the plants or garden beds to be

watered.

•

The downspout must be a rectangular 2" x 3" or 3" x 4"*

•

The barrel must be located within 28" (71cm) of the downspout to

use the fill hose provided.

•

The ground under the barrel must be level and firm. A solid surface

base of wood, pavers, or stone is recommended.

•

If the surface is not level, use a shovel or rake to grade the surface.

Check by placing a level on the rim of the barrel before continuing.

Installing the front fitting on the barrel

There are 2 options for installing the front fittings. Option A has a single

spigot at the bottom of the barrel and is recommended if you will only be

using a garden hose to access the water in the barrel. This configuration

gives access to most of the water in the barrel. A raised base is

recommended to increase water pressure. Option B has a mid-height

spigot and a bottom drain and is recommended for use with a watering

can.

Option A: Bottom spigot only

Find the front of the barrel; measure up 3" (76mm) from the bottom

of the barrel and mark the center for the spigot hole. Drill a hole using

the (SMALL) 1-1/4" hole saw included in the set.

2. Insert the threaded rubber seal into the hole.

shape for easier insertion.

3. Thread the spigot into the seal until the hex collar on the spigot sits

firmly against the seal and the water outlet points down.

or hand lotion on the internal threads will reduce friction and improve fit.

TIP

Pinch the threaded rubber seal

into a "U" shape before inserting

into the hole in the barrel.

Installing the fill hose seal

Locate the water inlet mark on the rim of the barrel (from Step 4).

Measure down 3" (76mm) and mark the center for the water inlet hole.

Make sure the inlet is located on a flat or evenly curved surface: avoid

ridges or other features that could affect the water seal.

2. Drill a single hole using the (MEDIUM) 1-1/2" hole saw included in the set.

3. Insert the fill hose seal into the hole.

for easier insertion.

About the FlexiFit diverter

DO NOT CUT THE DOWNSPOUT UNTIL READING THE ENTIRE GUIDE!

The FlexiFit diverter redirects water from your downspout to the barrel

and automatically passes water through the downspout when the barrel

is full of rainwater.

The diverter is installed in a hole that is cut in the downspout.

The hole must be cut at the correct height for the diverter to work

properly.

2. If the diverter is installed too low, the barrel will not fill properly.

3. If the diverter is installed too high, water will overflow from the rim

of the barrel (this only applies to open top barrels).

WARNING

Damage to home or

property may occur if

improperly installed.

Place the barrel in the intended location with the front facing out.

1. Mark the front of the barrel. This will be the side with the spigot facing

out. The spigot should be located on a flat or evenly curved surface without

ridges or features that can affect the water seal.

2. Hold the fill hose in position between the barrel and the downspout and

mark the water inlet location on the rim of the barrel. This mark can be at

the back, right, or left side of the barrel.

Check that the hose can reach horizontally from the rim of the barrel to the

downspout.

*Water capture percentage is reduced with 3"x 4" downspouts

28" MAX

(71cm)

Top View

Option B: Mid-height spigot with bottom drain

Mark the hole for the spigot. Find the front of the barrel, measure up

12" (30cm) from the bottom of the barrel and mark the center for the

mid-height spigot hole.

2. Mark the hole for the drain. Measure up 3" (76mm) from the bottom

of the barrel and mark the center for the drain hole.

connecting a garden or soaker hose to the drain fitting, we recommend

that the drain be located 6" (15mm) off center, to the left, or right side

of the spigot to give clearance for filling the watering can.

3. Drill 2 holes on these marks using the (SMALL) 1-1/4" hole saw included

in the set.

the hole saw after drilling the first hole.

Pinch the seal into a "U"

4. Insert 2 threaded rubber seals into both the spigot and drain holes.

Pinch the seal into a "U" shape for easier insertion.

Soapy water

5. Thread the spigot and drain into the seals until the hex collars sit firmly

against the seals.

improve fit.

TIP

Soapy water or hand lotion on the

hose cuff and rubber seal reduces

friction and makes insertion easier.

Optional

Stand

Option A

Pinch the seal into a "U" shape

Remove lid

before measuring

Back of barrel

IMPORTANT: There are two ways to install the diverter depending on the type

of barrel you use. If the barrel is a sealed container without a lid or screen, the

diverter can be located at the same level as the rim of the barrel or higher. This

will improve the filling efficiency of the diverter.

If the barrel has a removable lid or screen, the center of the diverter hole must

be drilled 3"(76mm) below the level of the rim of the barrel to prevent water

from leaking from the lid seam or screen. The diverter will not work if it is

placed below the level of the water inlet on the barrel.

The diverter provided in this kit is not for use with round downspouts.

A round downspout diverter available as an accessory at

www.earthmindedconsumerproducts.com

CORRECT

6" MIN

(15cm)

1-1/4"

(32mm)

Hole Saw

If you plan on

You may need to remove the plastic cut out from the end of

Soapy water or hand lotion will reduce friction and

12"

Option B

Inside Barrel

Outside Barrel

1-1/2"

(38mm)

Hole Saw

INCORRECT

If the hole is cut too low,

the barrel will not fill.

INCORRECT

For open top containers

only, If the hole is cut too

high, water will overflow

from the barrel rim.