EarthWay EV-N-SPRED C24HD Montage- und Betriebsanleitung - Seite 2
Blättern Sie online oder laden Sie pdf Montage- und Betriebsanleitung für Streuwagen EarthWay EV-N-SPRED C24HD herunter. EarthWay EV-N-SPRED C24HD 9 Seiten. Broadcast spreader
Auch für EarthWay EV-N-SPRED C24HD: Montage- und Betriebsanleitung (6 seiten), Montage- und Betriebsanleitung (10 seiten)
Seite drucken
C24HD & C24HDS
Assembly and Operating Instructions
PLEASE CONTACT US: IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY
QUESTIONS REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL
SUPPORT. SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, email: [email protected]
HELPFUL HINTS:
If your spreader does not spread evenly, be sure the FRONT on the gear box points to the front of the spreader. The impeller must
turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise. Clean the impeller after each use as some
fertilizer may become stuck on the impeller blades and will cause uneven spreading.
Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds will change
Clean and dry your spreader thoroughly after each use, wash between the shut-off plate and bottom of the hopper regularly. To
prevent rust, coat all metal parts (inside and out) including the frame tubes with a light oil or silicon spray.
Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
If you use Rock Salt remove the agitator to prevent damage to the gearbox and remove salt from the hopper daily. Rock Salt will
reconstitute back into a solid block if left in the hopper overnight and will damage your gearbox if pushed with the block in place.
IF YOUR SPREADER COMES SEMI ASSEMBLED, SKIP TO STEP #7
Upper Handle
Gauge & Lever
Handle
Shaft
Frame
Brace
Impeller
Frame
Gearbox
1. Remove and identify all of the loose parts from carton.
(Qty 4 #36214)
1/4-20 X 1½"
Phillips Panhead
Broadcast Spreader
Cross
Brace
Control
Rod
Lower
Handles
Pivot
Pivot
Rod
(Qty 4 #36300)
1/4-20 SS Locknut
2. Position hopper on side. Install frame using (4) 1/4-20 x 1 ½" Pan Head Phillips
machine screws and (4) 1/4-20 nylon insert locknuts. First put bolts through holes
in frame then through holes in bottom of hopper. Secure with locknuts. TIGHTEN
THESE LOCKNUTS NOW.
WARNING
DO NOT USE AIR TOOLS TO ASSEMBLE. TO PREVENT
SEIZING SPRAY ALL NUTS & BOLTS WITH FURNITURE
POLISH OR WAX
Gauge Overlay is snapped over
the metal gauge. Replace the stop
bolt assembly to secure overlay on
the gauge.
ROCK SALT AND POWDERED MATERIALS SHOULD
NOT BE USED IN THIS SPREADER AS IT WILL DAMAGE
GEARBOX AND CAN VOID WARRANTY.
USE ONLY GRANULAR MATERIALS.
36305
36300
Qty 2
Qty 17
36210
Qty 2
36214
36200
Qty 4
Qty 4
33117
Qty 1
36404
Qty 18
36105
Qty 1
36209
36103
Qty 4
Qty 1
36205
Qty 3
36207
Qty 2
1-2012 Pt# 52142
36104
Qty 1
PAGE 1