Dialogic Brooktrout TR1034 Schnelle Installation

Blättern Sie online oder laden Sie pdf Schnelle Installation für Computer Hardware Dialogic Brooktrout TR1034 herunter. Dialogic Brooktrout TR1034 2 Seiten. Did/did & loop start pci fax board
Auch für Dialogic Brooktrout TR1034: Installationshandbuch (2 seiten), Installation von (2 seiten)

Seite drucken

Installing the Dialogic®

Brooktrout® TR1034 T1/E1/IP

PCI Express Fax Board (Single

Span)

Part Number: 931-153-05

The

TR1034 T1/E1/IP

Dialogic® Brooktrout®

combination PCI Express boards

("TR1034" or

are full-sized, single slot,

"TR1034 Fax Board(s)")

PCI Express serial I/O bus-compatible boards with

T1/E1, Ethernet, and H.100 capabilities. The

TR1034 delivers 33.6 Kbps (V.34) fax transmission

speeds, up to 30 fax channels per board, and an

on-board T1/E1 interface (see Figure 6). The TR1034

includes an Ethernet connector for T.38 Fax over IP

and an H.100 connector to access off-board

resources.

The TR1034 T1/E1/IP PCI Express boards use 3.3V

and 12.0V power from the serial bus and can be

inserted in x4, x8, or x16 bus (signaling) slots.

You need a separate fax application to use the

TR1034 Fax Board. Please contact your application

provider (normally a third party vendor) for the

correct operating system driver, supporting files,

and firmware.

System Requirements

This board must be installed in an enclosure that

meets the following specifications.

A Pentium 4 or later host processor

A PCI Express serial I/O bus slot that is at least

x4 wide. See Recognizing PCI Express Slots for

more information.

Temperature: 0°C - 50°C

Humidity: 10% - 90% (noncondensing)

Power requirements:

3 W at 3.3 VDC

5 W at 12.0 VDC

8 W total power

Setting the Module Number

You must set each TR1034 Fax Board to a unique

module number to identify the resources associated

with a specific board in a multi-board system. Use

the rotary switch (Figure 1) to set the module

number for each TR1034 Fax Board (see location in

Figure 4). The available settings are 2 - F (0 and 1

are reserved).

Figure 1

Rotary Switch

Using the H.100 Clock Termination Switch

On a single TR1034 or on multiple TR1034 Fax

Boards installed in the same chassis, leave the

H.100 clock termination switch (Figure 4) in the

OFF position. Multiple TR1034

Boards in the

Fax

same system do not require the use of a connecting

H.100 cable.

If you have a TR1034 and other boards that need to

be connected using an H.100 cable (not supplied),

you must terminate the H.100 clock signal. Only the

boards at each end of the cable must be terminated.

All other boards must not be terminated (see

Figure 2).

Mounting

Module Number

Bracket

Switch

T1/E1

Connector

T1/E1

Status LED

Ethernet

Connector

Board

Status LED

PCI Express Connector

Figure 4

Dialogic

Brooktrout

TR1034 T1/E1/IP/Ethernet

PCI Express Fax Board

Set the H.100 switch

to the ON position.

Set H.100 switches

on these boards to

the OFF position.

Set the H.100 switch

to the ON position.

Figure 2

Setting Clock Termination in a Series of Boards

Connected by an H.100 Bus

An H.100 termination switch (see Figure 3) controls

termination for the H.100 clock signals. Set the

switch to ON to terminate the H.100 clock on a

TR1034 Fax Board (see Figure 4 for the location of

the switch on the board).

Push switch

toward mounting

bracket to

turn on.

Figure 3

H.100 Clock Termination Switch

H.100 Clock

Termination Switch

H.100 Connector

Safety Compliance Statements

Install this board only in UL Listed equipment

that has instructions stating that the user may

install and remove accessory boards.

Disconnect any TNV circuit connectors

(telephone line cords) from this board before

removing the cover of the equipment.

Installing the Dialogic® Brooktrout® TR1034

Fax Board

Caution: A small amount of static electricity can

destroy the sensitive components on your board.

To prevent static damage, always connect yourself

to ground using a ground strap before touching a

circuit board. Handle boards only by the edges or

metal mounting brackets and transport boards in

an anti-static bag.

To install the board:

1. Power off the computer.

2. Remove the computer cover. If the system has a

board hold-down bar, remove it as well.

3. Locate an unused PCI Express bus slot (see

Figure 5).

4. Holding the TR1034 Fax Board at each top

corner, insert the board firmly into the PCI

Express slot.

5. Screw the board's mounting bracket securely to

the computer's frame. See Figure 4.

6. Attach the connector on the H.100 cable to the

connector on the board, if needed.

7. Replace the computer cover.

8. Turn on the computer.

The board status LED (see Figure 4)

continuously flashes yellow when you turn the

computer on.

Warning: When installing the board, be sure that

the mounting bracket is securely fastened to the

chassis and the chassis is plugged into a

grounded three prong plug. Improper chassis or

bracket grounding can result in harmful or fatal

electrical shock as well as component damage.

Note:

Dialogic® Brooktrout® Fax Boards should not be

present in the computer during the installation of any

operating system. The operating system can

misinterpret the board as being some other device, with

unpredictable consequences.