Dialogic DM/IP481-2T1-PCI-100BT Schnellinstallationskarte

Blättern Sie online oder laden Sie pdf Schnellinstallationskarte für Netzwerk-Hardware Dialogic DM/IP481-2T1-PCI-100BT herunter. Dialogic DM/IP481-2T1-PCI-100BT 2 Seiten. Dm/ip boards or pci 100 base-t

Seite drucken

Dialogic

DM/IP Boards

Quick Install Card for PCI 100 Base-T

DM/IP481-2T1-PCI-100BT

DM/IP601-2E1-PCI-100BT

Part number 64-0031-02

Dialogic Corporation.

Before You Begin

Protecting the Board from Damage

Caution! All computer boards are sensitive to

electrostatic discharge ("ESD"). Handle all static-

sensitive boards and components at a static-safe work area,

and observe anti-static precautions at all times.

If you are not familiar with ESD safety precautions, visit

http://www.dialogic.com/support/hwinstall

Unpacking the Board

Unpack the Dialogic

DM/IP Board ("board") according

to the following steps:

Prepare a static-safeguarded work area.

Carefully remove the board from the shipping

carton and anti-static packaging. Handle the

board by the edges and avoid touching the

board's components.

Lay the board on the static-dissipative work

surface.

Note: Place boards in static-shielding bags when carrying

boards from station to station.

CAUTION: Do not remove the board from the anti-static

packaging until you are ready to install it. Observe proper

anti-static precautions at all times.

Configuring the Hardware

Board Identification

The DM3 device driver, part of the system software,

assigns board instance numbers in ascending order

(beginning with 0) as it detects each board in your system.

A board instance number is the board identification

number used by the system software to recognize the

board. Refer to the Dialogic

Configuration Manager

*Channels:

Yellow

Green

Loopback

to learn more.

(DCM) utility to retrieve the board instance (ID)

number(s) assigned to the board(s) in your system.

NOTE: If you add a board to the system, the existing

board instance (ID) numbers may change, depending upon

the PCI bus and slot number where the new board is

installed.

The system software does not recognize or use the setting

number of the rotary switch (SW1) to determine the board

ID number. However, you must set SW1 to a unique

number for each DM3 board in your system so that the

power on self test for the board(s) can complete

successfully.

Use a non-magnetic screwdriver to turn SW1 to one of the

15 board ID settings, 1-9 and A-F.

See the DCM On-Line Help for more details on board

identification.

Installing the Hardware

NOTE: If you are running in a Windows NT

environment, install the software, install the board(s), and

Physical Description

4 3 2 1

Red

Ethernet Interface Connector

Good Link LED

RJ-48C jacks: Connectors (4) to external

digital telephone network interface.

General Network Interface Alarm LED

Power LED

Reset LED

SW1: Rotary switch to set board

identification (UNIX systems only).

Alarm LEDs: Indicate network alarms for

each trunk.

Red: Alarm to indicate loss of signal.

Yellow: Alarm to indicate loss of frame

synchronization at far end of external

network.

Green: Indicates signal present; powered up

and receiving signal from external sources.

Loopback: Indicates loopback mode is

activated.

CT/MVIP Bus Termination Jumpers*:

Bus signal is terminated when the

JP2A

corresponding jumper is installed.

JP2B

JP2A: CT Bus termination jumper

JP2B: MVIP Bus termination jumper

10. P3: CT Bus connector

11. ISA Edge Retainer

12. Signal Processing Daughterboard

*Note: Signal must be terminated only on

boards at each end of the CT Bus cable.

then run the Dialogic

Configuration Manager (DCM) to

configure the system.

1. With your computer on the static-safe work area,

switch off the power and disconnect all power cords

from the electrical outlets.

2. Remove the cover, select an empty expansion bus

slot, and remove the slot's retaining screw and

access cover plate.

3. Use the slot's board guides as you insert the board

edge connector into the slot. Press firmly until the

board is securely seated in the slot. If you are not

installing your board in an ISA form factor PCI slot,

remove the ISA edge retainer.

4. Replace and tighten the retaining screw to secure the

board.

5. Select a new slot and repeat steps 3 and 4 for each

board you are installing.

6. Use the CT Bus cable to connect the board you are

installing to other boards in the system.

NOTE: Your system may include both CT Bus boards

and SCbus boards. To connect both board types, you