Dialogic DM/IP601-CPCI-100BT Schnellinstallationskarte

Blättern Sie online oder laden Sie pdf Schnellinstallationskarte für Netzwerk-Hardware Dialogic DM/IP601-CPCI-100BT herunter. Dialogic DM/IP601-CPCI-100BT 2 Seiten. Ip board

Seite drucken

Dialogic

DM/IP601-CPCI-100BT

IP Board

Quick Install Card

Part number 64-0027-02

Dialogic Corporation.

Before You Begin

Protecting the Board from Damage

CAUTION: All computer boards are sensitive to

electrostatic discharge ("ESD"). Handle all static-sensitive

boards and components at a static-safe work area, and

observe anti-static precautions at all times.

If you are not familiar with ESD safety precautions, visit

http://www.dialogic.com/support/hwinstall

Unpacking the Board

Unpack the Dialogic

DM/IP601-CPCI-100BT board

("board") according to the following steps:

Prepare a static-safeguarded work area.

Carefully remove the board from the shipping

carton and anti-static packaging. Handle the

board by the edges and avoid touching the board's

components.

Lay the board on the static-dissipative work

surface.

Note: Place boards in static-shielding bags when carrying

boards from station to station.

CAUTION: Do not remove the board from the anti-static

packaging until you are ready to install it. Observe proper

anti-static precautions at all times.

Installing the Hardware

NOTE: In a Windows environment, install the software

first, the hardware second, and then run the Dialogic

Configuration Manager (DCM) to configure the system.

1. Turn the power to the chassis OFF if you do not have a

live insertion system. If you do have live insertion

capability, the power to the chassis can remain ON.

2. Remove the chassis cover plate or open the front door.

3. Select an empty expansion bus slot.

Board

Extractor

POWER

RED

YEL

Alarm

CARR

SGNL

LOOP

Status

LEDs

RED

YEL

CARR

SGNL

LOOP

OUT OF

SERVICE

Board

Extractor

Faceplate

(front view)

Compact PCI Baseboard

Part:

to learn more.

Power LED

Red Alarm LEDs

Yellow Alarm LEDs

Carrier Signal LEDs

Loopback LEDs

Out of Service LED

P1, P4, P5

NOTES: Rear I/O Modules are ordered separately and are available in two different forms depending

NOTE: When power is on, the Rear I/O module should be

installed first, before the main board.

4. Install the Rear I/O module in the rear of the slot

selected in step 3. Use the slot's board guides as you

insert the board into the chassis slot. Make sure that the

tabs on the board extractors engage the guide holes in

the chassis card cage, then lock down the board

extractors until the red locking tabs snap shut.

cPCI backplane pins are bent easily. Make sure that

the board is seated with hand pressure before fully

seating board. If board extractors are used to seat

Physical Description

Daughterboard

Baseboard

Compact PCI Board

Function:

Indicates board is powered up.

Not functional in this assembly.

Indicates board is out of service

or in reset from host.

Compact PCI board connectors

to backplane.

on the type of connectors used, guided or unguided. Select a Rear I/O Module that is

compatible with your chassis type. See the PICMG 2.0 D3.0 Compact PCI Specification for

more information on guided and unguided connectors.

CAUTION

the board, make sure to seat evenly.

E th e rn e t

In te rfa c e

C o n n e c to r

P 5

T ru n k 1

T ru n k 2

J 1 -J 4

R J -4 8 C J a c k s

T ru n k 3

T ru n k 4

P 2

T-1 and E-1 120-Ohm

Rear I/O Module

Rear I/O Modules

Part:

Function:

J1–J4

Not functional in this assembly.

Telephony network interface test port

Rear I/O module connector to Compact PCI

backplane

BNC

Not functional in this assembly

Connectors

Ethernet

Connection to Ethernet network

Connector

5. Install the board in the front of the slot selected in step 3.

Use the slot's board guides as you insert the board into

the chassis slot. Make sure that the tabs on the board

extractors engage the guide holes in the chassis card

cage, then lock down the board extractors until the red

locking tabs snap shut.

NOTE: If the power to the chassis is on, power is

automatically applied to the board, the Out of Service

LED lights briefly and then goes out, and the Power

LED goes on.

6. Tighten the retaining screws to secure the board firmly

in the chassis slot (optional).

7. Select a new slot and repeat steps 4-6 for each board you

E th e rn e t

In te rfa c e

C o n n e c to r

P 5

B N C C o n n e c to rs

P 2

E-1 75-Ohm

Rear I/O Module