ABB Decento 5519K-C Series Installationshandbuch - Seite 3

Blättern Sie online oder laden Sie pdf Installationshandbuch für Industrielle Ausrüstung ABB Decento 5519K-C Series herunter. ABB Decento 5519K-C Series 4 Seiten.

Seite drucken

ABB Decento 5519K-C Series Installationshandbuch

Installation manual for products

by ABB s.r.o., Elektro-Praga

This manual applies to the following devices

of the Decento

range:

- switches Ord. Nr. 3559K-C.....

- socket outlets Ord. Nr. 5519K-C.....

- communication sockets Ord. Nr. 5014K-C.....

- TV+R+SAT outlets Ord. Nr. 5011K-C.....

ABB s.r.o.

Elektro-Praga

Resslova 3

466 02 Jablonec n. N.

Czech Republic

http://www.abb.cz/elektropraga

E-mail: [email protected]

1. Important Notices

The devices from Decento

range contain fragile porcelain parts,

which require caution during handling and installation.

Household wiring accessories work with electric voltage 230 V AC, it means

with voltage dangerous to life.

The installation of the instruments can be carried out only by person-

nel with corresponding electro-technical qualification.

The relevant electric circuit must be de-energized before start of installing. It

has to be ensured that the circuit cannot be switched on by other personnel.

Carry out a check (by voltage tester or measuring apparatus) that the circuit

has been really switched off. Use the same principles also when replacing

the device.

It is not allowed to use the devices for other than specified purposes, or for

different than prescribed voltages.

It is prohibited to use the devices at places with a risk of their flooding,

splashing by water, or at places with excessive dustiness that could cause

reducing their function and safety. This condition is not valid for the devices

that are intended for this type of environment and that are marked with

relevant degree of protection IP xx according to EN 60 529.

2. Conditions for using frames

Some frames are manufactured from wood, and it is necessary to ensure

optimum conditions during their use and storage:

Relative humidity of air: 30-60% at room temperature (approximately

20 °C)

If suitable conditions are not maintained, surrounding parameters can lead

to a change of dimensions and bending or twisting of the frame.

3. Preparation for Installation of Flush-Mounted Devices

If it is not determined differently, the devices are installed under the plaster

into wiring boxes. The following principles must be followed in order to

secure a correct installation:

a) The devices must be attached into suitable wiring boxes with

corresponding inner depth.

b) It is not necessary to use boxes with fixtures for solid partitions and

walls. Boxes with fixtures must be used for hollow partitions or plaster-

board partitions.

c) Distance of wiring box centres about 90 mm must be observed in case of

Decento

devices installations at horizontal or vertical directions.

d) Pay attention to the setting of the flush-mounted boxes during execution

of the construction works. The box must not protrude above the wall

surface after the plaster application and it must not be embedded below

the surface of the plaster either.

e) Conductor length in the wiring box must be about 13 cm.

f) Devices of Decento

range are always supplied as a complete set; it

means insert, cover and frame in one package.

4. Conductor Connection and Insert Fixing

Clamps of inserts are intended for tough solid conductors and tough

stranded conductors. (The core of tough stranded conductors consists of

7 wires.)

In case of standard inserts, screw-less clamps are used for the

conductors with cross-section of 1.5 - 2.5 mm

not specified differently. The length of conductor stripping is specified on

the insert. Secure that the stripped conductor ends are straight and

without any deformation.

In case of inserts with screw-less clamps just insert the conductor into

the respective chamber of the clamp; clamps with screws require

tightening.

Marking of the clamps corresponds to their function in the electric circuit.

Neither orientation nor signalling glow lamps can be used for Decento

range.

Shape the conductors during installing the inserts into the boxes in such

a way that they cannot be released from the clamps.

Check correctness and strength of the conductor fixing in the clamps. If

conductors in screw clamps are loosened tighten them again. In case of

inserts with screw-less clamps, the conductor is fixed continuously by

a pressure in the clamp chamber.

N-3559K-E100

5. Assembly and Disassembly of Devices

(3D-2013/02)

5.1 Frame placing

The frame must be placed on the insert in such a way that the fixing screws

fit into the frame slits. The frame must fit closely on the plaster.

5.2 Switches

The switch structure is shown in the Figures No. 1, 2. The porcelain handle

on carrier is inserted into the insert control handle. The cover is attached by

means of 2 screws to the insert.

Switch disassembly is done by unscrewing the cover from the insert and by

removing the frame.

N-3559K-E100

Tel.: +420 483 364 111

Fax: +420 483 364 159

Fig. 1: Assembly of switch with cover and frame

Abb. 1: Schalterzusammenbau mit Abdeckung und Rahmen

Рис. 1: Сборка выключателя с крышкой и рамкой

Fig. 2: Assembly of switch with double handle, cover and frame

Abb. 2: Schalterzusammenbau mit 2-teiligem Knebel, Abdeckung u. Rahmen

Рис. 2: Сборка выключателя с рычажком из 2 частей, крышкой, рамкой

5.3 Socket outlets

Attach the socket cover to the insert by means of the centre screw. The

screw also fixes the frame.

Socket disassembly is done by unscrewing the cover from the socket insert

and by removing the frame.

Plug in only plugs intended for this purpose into the sockets. Remove the

plug from the socket only by grasping the plug with the hand. Do not pull

the cable. Do not insert any other objects into the socket holes.

Fig. 3: Assembly of socket with cover and frame

Abb. 3: Zusammenbau der Steckdose mit Abdeckung und Rahmen

Рис. 3: Сборка розетки с крышкой и рамкой

5.4 Communication Sockets

The communication socket contains the base with two holes 19.4 x 14.8

mm for attachment of connectors. Installation of connectors and cables is to

be done according to the relevant standards on the cable system

installation.

Attach the socket cover to the insert by means of the centre screw. The

screw also fixes the frame.

Socket disassembly is done by unscrewing the cover from the socket insert

and by removing the frame.

Cu, if the conditions are

Fig. 4: Assembly of communication socket

Abb. 4: Zusammenbau der Kommunikationssteckdose

Рис. 4: Сборка телефонной розетки

5.5 TV+R+SAT Sockets

The TV+R+SAT socket contains the insert for connection to the coaxial

cable. Installation of the insert and the cables is to be done according to the

relevant standards on installation of distribution systems for TV+R+SAT.

Attach the socket cover to the insert by means of centre screw. The screw

fixes also the frame.

Socket disassembly is done by unscrewing the cover from the socket insert

and by removing the frame.

Switch cover

Schalterabdeckung

Крышка выключателя

Frame

Rahmen

Рамка

Switch insert with handle

Schaltgerät mit Knebel

Механизм выключателя с рычажком

Fig. 5: Assembly of TV+R+SAT socket

Abb. 5: Zusammenbau der TV+R+SAT-Steckdose

Рис. 5: Сборка розетки TV+R+SAT

6. Devices Maintenance

Maintenance of mechanical and electrical parts of the devices is not

necessary.

Any modifications that would damage or destroy function and safety

Switch cover

Schalterabdeckung

of the instruments are prohibited.

Крышка выключателя

Maintenance and possible repairs of wiring and wiring accessories

can be carried out only by personnel with the corresponding electro-

technical qualification. Always contact a specialized company in case

Frame

of any failure or malfunction.

Rahmen

Рамка

Wipe the covers by soft duster. Dirty covers can be cleaned with a cloth

slightly wetted with mild soap solution and then can be dried with a dry

cloth. Never wipe or clean device covers with any rough cleaning clothes or

Switch insert with handle

preparations that contain hard sharp parts.

Schaltgerät mit Knebel

Do not use aggressive chemical substances (petrol, acetone, etc.).

Механизм выключателя с рычажком

In case of interior painting it is recommended to remove the covers and to

strap the inserts with a suitable tape so that possible impurities cannot

penetrate into the inserts. (Relevant electric circuits must be de-energized

before the cover removal.)

7. Disposal

The way of application or disposal of unused parts of the products is

regulated by the relevant legal directives valid in your country.

8. Product Information

Further information on the products of ABB s.r.o., Elektro-Praga is available

at internet address: www.abb.cz/elektropraga and also in the printed

Catalogue of household wiring accessories issued by this Company.

Socket cover

Abdeckung der Steckdose

Company address:

Крышка розетки

ABB s.r.o., Elektro-Praga

Resslova 3

466 02 Jablonec nad Nisou

Czech Republic

Frame

Rahmen

Рамка

Installationsanleitung für Produkte

von ABB s.r.o., Elektro-Praga

Socket insert

Diese Anleitung ist gültig für die folgenden Geräte

Steckdosengerät

der Reihe Decento

Механизм розетки

- Schalter Best. Nr. 3559K-C.....

- Steckdosen Best. Nr. 5519K-C.....

- Kommunikationssteckdosen Best. Nr. 5014K-C.....

- TV+R+SAT-Steckdosen Best. Nr. 5011K-C.....

1. Wichtige Hinweise

Die Geräte der Reihe Decento

die Vorsicht bei der Handhabung sowie bei der Installation erfor-

dern.

Die Geräte für Hauselektroinstallationen arbeiten mit der elektrischen Span-

nung 230 V AC, d. h. mit der lebensgefährlichen Spannung.

Die Geräte darf nur die Person mit der entsprechenden elektrotechni-

schen Qualifikation installieren.

Vor der Einbaueinleitung muss der jeweilige Stromkreis von der Stromver-

sorgung getrennt werden. Gleichzeitig muss es sichergestellt werden, dass

Socket cover

unerwünschte Einschaltung seitens anderer Personen nicht erfolgen kann.

Abdeckung der Steckdose

Vor dem eigentlichen Einbau ist es notwendig, sich zu vergewissern (mit

Крышка розетки

dem Prüf-, Messgerät), ob die Abtrennung wirklich erfolgte. Das gleiche gilt

auch beim Austausch der Geräte.

Frame

Es ist nicht erlaubt, die Geräte anders als bestimmungsgemäß oder für an-

Rahmen

dere als vorgeschriebene Spannungen zu benutzen.

Рамка

Es ist verboten, die Elektroinstallationsgeräte dort zu verwenden, wo ihre

Überschwemmung, Vollspritzung mit Wasser bei Benutzung auftreten könn-

te oder wo ihre Funktionstauglichkeit und Sicherheit infolge von der über-

Socket insert

mäßigen Verstäubung beeinträchtigt würde. Diese Bedingung gilt bei den

Steckdosengerät

Geräten nicht, die für den gegebenen Umgebungstyp vorgesehen sind und

Суппорт розетки

die mit der entsprechenden Schutzart IP xx nach der Norm EN 60 529 ge-

kennzeichnet werden.

Socket cover

Abdeckung der Steckdose

Крышка розетки

Frame with colour marking

Rahmen mit Farbzeichen

Рамка

Socket insert

Steckdosengerät

Механизм розетки

Tel: 483 364 111

Fax: 483 364 159

E-mail:

[email protected]

enthalten spröde Porzellanteile,