3B SCIENTIFIC PHYSICS U10362 Anleitungsblatt - Seite 2

Blättern Sie online oder laden Sie pdf Anleitungsblatt für Laborausrüstung 3B SCIENTIFIC PHYSICS U10362 herunter. 3B SCIENTIFIC PHYSICS U10362 4 Seiten. Ballistic pendulum

Seite drucken
within the device. The sphere is then pushed down
inside the barrel using the ramrod until the de-
sired spring tension has been reached. The ram-
rod should not be removed too quickly, otherwise
the suction its removal produces may pull the
sphere out with it. The position of the sphere may
only be checked using the observation holes. Never
look into the barrel!
• Before launching, ensure that no one is in the way
of the trajectory. To launch, the cord of the launch-
ing lever is briefly pulled perpendicularly to the
lever.
• The pendulum
8
can be removed by undoing the
bearing screw
and turned by 180° so that it is
4
installed with the rear of the projectile catcher
9
pointing towards the launcher (experiments on
elastic collision). The counter bearing
so that the pendulum hangs at a slight angle if the
bearing screw is only light tightened. This means
that the projectile catcher is not precisely in front
of the launch aperture of the launcher. For this rea-
son, the bearing screw should be tightened until
the catcher and the launch aperture are in line.
• After turning the pendulum round, or if necessary,
the guide
for the swing pointer
3
adjusted so that the pointer just touches it when
the pendulum is suspended at rest. The screw on
the guide should only be finger-tightened to avoid
the appearance of pressure on the pendulum rod.
• Maintenance: the ballistic pendulum principally
requires no maintenance. If necessary some non-
acidic grease (Vaseline) can be applied to the bear-
ing screw
and the knurled screw
4
in the vicinity of the scale, the apparatus may be
cleaned using acetone, ethanol (white spirit) or
petroleum ether as required. Avoid submerging the
equipment in water.
4. Experiment procedure and evaluation
4.1 Ballistic pendulum
4.1.1 Experiment setup
•
The experiment setup corresponds to Fig. 1 for
experiments on inelastic collision. For experi-
ments on elastic collisions, the pendulum should
be turned round by 180° (cf. Section 3 "Opera-
tion").
4.1.2 Experiment procedure
•
It is practical for these experiments to enter the
experiment number, the spring tension (1, 2 or
3), the type of collision (inelastic "i" or elastic "e"),
the number of extra weights used and the mea-
sured angle ϕ. In order to obtain the most accu-
rate experiment results, after one shot, a second
should be performed with the swing pointer not
having been reset to 0° in between. This mini-
mizes the unavoidable frictional losses of the
swing pointer.
•
Example experiment sequence:
No
1
2
3
4
5
6
7
8
9
4.1.3 Experiment evaluation
4.1.3.1 Inelastic collision
• The following equation is valid for the swinging
is designed
5
should be
6
•
. Other than
bn
Fig. 2: Determining the required lengths. Distance between center of gravity
and axis of rotation (I
additional weights when the collision is inelastic. To perform the measure-
ment, the pendulum may, for example, be balanced on a ruler mounted on
its side. The distance between the center of the projectile and the axis of
rotation is I
•
•
6
Spring
Type of
tension
collision
1
i
2
i
3
i
1
i
2
i
3
i
1
e
2
e
3
e
pendulum due to conservation of energy
E
= E
pot
kin
where the potential energy is
g ∆h
E
= m
pot
tot
Here is m
the total mass of the pendulum in-
tot
cluding the projectile and any extra weights, g is
the acceleration due to gravity and ∆h is the dif-
ference in height of the center of gravity of the
pendulum at rest and at the maximum extent of
its swing.
From the measured angle ϕ and the measured
length I
to the center of gravity according to Fig.2
s
the following is derived:
∆h = I
(1 – cos ϕ)
s
) should be measured including the projectile and any
s
= 280 mm.
K
The kinetic energy can be calculated from the
moment of inertia I
relative to the axis of rota-
tot
tion and the maximum angular speed ω accord-
ing to the equation
1
2
=
ω
E
I
kin
tot
2
If Equations 2 and 4 are inserted into Equation 1
and ∆h eliminated using Equation 3 then the
equation can be rearranged to:
Angle ϕ
Extra
weights
0
17.5
0
25.0
0
36.0
2
9.5
2
13.5
2
19.0
0
29.5
0
42.0
0
60.0
(1)
(2)
(3)
(4)