HP ProCurve 1600M Installationshandbuch - Seite 23

Blättern Sie online oder laden Sie pdf Installationshandbuch für Schalter HP ProCurve 1600M herunter. HP ProCurve 1600M 28 Seiten. Redundant power supply
Auch für HP ProCurve 1600M: Spezifikationsblatt (12 seiten), Lies mich zuerst (8 seiten), Handbuch für Rezensenten (27 seiten), Ergänzendes Handbuch (2 seiten), Ergänzendes Handbuch (2 seiten), Installationshandbuch (28 seiten), Installationshandbuch (36 seiten), Handbuch zur Schnelleinrichtung (2 seiten), Handbuch zur Schnelleinrichtung (4 seiten), Benutzerhandbuch (8 seiten), Handbuch Ergänzung (28 seiten), Lies mich zuerst (16 seiten), Montage und Demontage (2 seiten), Installationshandbuch (12 seiten), Handbuch für Planung und Durchführung (40 seiten), Anweisungen zur Demontage des Produkts nach Ablauf der Lebensdauer (2 seiten), Installationshandbuch (46 seiten), Diagnostik-Handbuch (2 seiten), Anweisungen für die Demontage (2 seiten)

Seite drucken
HP ProCurve 1600M Installationshandbuch

Mode Conditioning Patch Cord for Gigabit-LX

Mode Conditioning Patch Cord for
Gigabit-LX
The following information applies to installations in which multimode
fiber-optic cables are connected to a Gigabit LX Transceiver installed in the
Gigabit Stacking Module.
Unlike Gigabit SX, which connects to only multimode fiber-optic cabling,
Gigabit LX can use either single-mode or multimode cable. Multimode cable
has a design characteristic called "Differential Mode Delay", which requires
that the transmission signals be "conditioned" to compensate for the cable
design and thus prevent resulting transmission errors. Since Gigabit SX is
designed to operate only with multimode cable, Gigabit SX transceivers can
provide that transmission conditioning internally.
Gigabit LX transceivers, since they are designed to operate with both single-
mode and multimode cable, do not provide the transmission conditioning
internally. Thus, under certain circumstances, depending on the cable used
and the lengths of the cable runs, an external Mode Conditioning Patch
Cord may need to be installed between the Gigabit LX transmitting device and
the multimode network cable to provide the transmission conditioning.
If you experience a high number of transmission errors on the Gigabit LX
ports, usually CRC or FCS errors, you may need to install one of these patch
cords between the Gigabit LX port in your switch and your multimode fiber-
optic network cabling, and between the Gigabit LX transmission device and
the network cabling at the other end of the multimode fiber-optic cable run.
A patch cord must be installed at both ends.
The patch cord consists of a short length of single-mode fiber cable coupled
to graded-index multimode fiber cable on the transmit side, and only multi-
mode cable on the receive side. The section of single-mode fiber is connected
in such a way that it minimizes the effects of the differential mode delay in the
multimode cable.
N o t e
Most of the time, if you are using good quality graded-index multimode fiber
cable that adheres to the standards listed on page 8, there should not be a need
to use mode conditioning patch cords in your network. This is especially true
if the fiber runs in your network are relatively short.
If you are using single-mode fiber-optic cabling in your network, there is no
need to use mode conditioning patch cords. Connect the single-mode network
cable directly to the Gigabit LX transceiver.
17