Aquatek ATCBF-AS Handbuch für Betrieb und Wartung - Seite 11

Blättern Sie online oder laden Sie pdf Handbuch für Betrieb und Wartung für Water Filtration Systems Aquatek ATCBF-AS herunter. Aquatek ATCBF-AS 19 Seiten. Arsenic systems

Seite drucken

United Water Inc.

Installation & Replacement of Media Pak

These instructions are to help guide you through the steps for initial installation or replacement of

the media in your filter or softener. Please check to ensure that all the parts have been included

by reviewing the labels that are attached to the filter (e.g. xxx bed - container 1 of 3, 2

of 3, 3 of 3). Container may contain more than one media. lf you have any questions regarding

the installation or replacement of your media bed, please contact your local dealer for assistance.

1. Loading the Media Pak

Place the distributor tube into the media tank and

plug the end of the distributor tube with a tape to

prevent media from entering it. Make sure that

distributor tube is inside the tank and seated in a

depression at the bottom of the tank. (If replacing the

media. inspect the distributor for any damage to the

slots in the cone or plugging - clean if necessary.)

Plug tube with a tape

Remove after media

is loaded.

Fig. 1 - The riser

Fig. 2 - Fill support

(distributor) remains

bed first (if supplied)

inside the tank seated

in the depression at

the bottom. The riser

should be capped to

prevent resin beads

from getting inside.

Plug the media tube with tape to prevent the media

from getting inside the tube. Place the media into

the tank in the order indicated on the next page for

the type of unit that matches yours. The large funnel

(supplied) makes filling the tank easier and heater.

(Or an empty 1 gallon or 4 liter container with the

bottom cutout makes a good funnel.) Fill support bed

(if supplied) first. During the filling process, ensure

the distributor tube stays on the bottom of the tank,

reasonably centered. Remove the

tape from the distributor once media

is loaded. Whenever possible, fill the

tank outdoors to avoid problems with

dust. lf filling indoors, a dust mask

should be worn.

Media Fill/Replacement

Fig. 3 - The media will

not always spill down

inside the tank and

may need to be swept

inside

UNITED WATER INC.

AtCBF-AS-S

quAtek

2. Placing the Unit in Service

Once the tank is filled, remove the cover from the

distributor and clean off the top of the tank. Place

the control valve onto the tank, ensuring the

distributor fits into the valve properly. Tighten the

valve onto the tank using moderate force. Applying

some household liquid soap to the main seal

O-ring will ease assembly. Attach the plumbing to

the inlet and outlet of the valve as necessary

Follow the installation and operating instructions

for system start-up found in your Owners Manual

or slowly fill the tank in the backwash position and

allow it to flush the air and fine particles down the

drain until the drain water appears clear (about 20

minutes). Once the drain runs clear, plug in the

electrical cord, open the inlet valve fully and allow

the valve to finish its cycle. Check for any leaks

and reset the time of day on your controller.

3. Depressurizing the Unit*

The first step is to loosen the bed and depressurize

the unit. Place the unit into the backwash position

and keep it there by unplugging the unit from the

power supply. Allow it to backwash for several

minutes to loosen the bed. To depressurize, simply

shut off the water supply to the unit either at the

main or use the bypass to the unit.

4. Removal of Old Media*

Next remove the control valve and empty the tank.

You may have to disconnect plumbing from the

inlet and out let of the valve. depending on the type

of valve your filter or softener has. insert a piece of

1/2" flexible hose into the distributor and siphon the

water into the drain. Remove the distributor tube

from the tank. Flush out all the contents into a

large pail or garbage can by elevating the tank as

required (dictated by container used to hold old

media). Lay the tank on its side and insert a

garden hose into the tank. Make sure the tank is

completely empty before proceeding.

* for replacement of media only

erieS

Ser

uide