HP V1405-5 Installationshandbuch - Seite 2
Blättern Sie online oder laden Sie pdf Installationshandbuch für Schalter HP V1405-5 herunter. HP V1405-5 2 Seiten. Hp v1405-5 switch (jd866a) hp v1405-8 switch (jd867a) hp v1405-5g switch (jd869a) hp v1405-8g switch (jd871a)
Seite druckenIntroduction
Thank you for purchasing this Switch. This high quality
Switch is an easy, efficient way of creating a network or
expanding an existing network. The Switch's Gigabit/Fast
Ethernet ports (depending on model) provide support for
bandwidth intensive applications, and allow highspeed
connections to servers, and to the rest of the network.
Your package contains:
• Switch
• Power adapter for use with the V1405-5G and 1405-8G,
or power cord for use with the V1405-5 and V1405-8
• Four rubber feet
• This installation guide
• Support and Safety Information sheet
• Warranty flyer
NOTE: This guide will use the terms Switch 5/8 when referring to HP V1405-
5/8 Switch and Gigabit Switch 5/8 when referring to HP V1405-5G/8G
Switch.
WARNING: Please read the 'Important Safety Information' section in
the Support and Safety Information sheet before you start.
VORSICHT: Lesen Sie zuerst im Informationsblatt mit Support- und
Sicherheitshinweisen den Abschnitt „Wichtige Sicherheitshinweise".
ADVERTENCIA: Antes de empezar, lea la sección "Información
importante sobre seguridad" de la hoja Información de soporte y
seguridad.
AVISO: Leia a seção 'Informações Importantes sobre Segurança' na
folha Informações de Suporte e Segurança antes de você começar.
AVERTISSEMENT : Avant de commencer, veuillez prendre
connaissance des informations de la section « Informations
importantes sur la sécurité » de la fiche Informations relatives à
l›assistance et à la sécurité.
Configuration
Switch: Desktop PC
Desktop PC
Gigabit Switch:
Workstation requiring
High Bandwith
Connection
Switch/
Gigabit Switch
Gigabit Switch only:
1000 Mbps
Connections
Wireless 1 1g
Access Point
Sample configuration with Switch or Gigabit Switch.
Positioning Your Switch
When positioning your Switch, ensure:
• It is out of direct sunlight and away from sources of heat
• Cabling is away from power lines, fluorescent lighting fixtures,
and sources of electrical noise such as radios, transmitters and
broadband amplifiers
• Water or moisture cannot enter the case of the unit
• Air flow around the unit and through the vents in the side of
the case is not restricted. It is recommended that you provide a
minimum of 25 mm (1 in.) clearance
Using the Rubber Feet
Use the four self-adhesive rubber feet to prevent your Switch from
moving around on your desk, or when stacking with other units.
Only stick the feet to the marked areas at each corner on the
underside of your Switch.
Wall Mounting
There are two slots on the underside of the Switch that can be used
for wall mounting. The Switch must be mounted with the LEDs facing
upwards.
About Your HP V1405-8 Switch
Front
1
2
Illuminated Power Status Logo (White)
1
Indicates that the Switch is powered on. If the LED is off, there
may be a problem. Refer to Problem Solving.
2
Five/Eight Port Status LEDs (Blue)
If the LED is on, the link between the port and the next piece
of equipment is OK. If the LED is flashing, the link is OK and
data is being transmitted or received. If the LED is off, nothing
is connected or the connected device is turned off, or there is
a problem with the connection (refer to the Problem Solving
section).
NOTE: Product may vary from model shown.
Mounting Instructions for Cement Walls
Make two holes 124 mm (4.9 in.) apart and insert two nylon or
similar screw anchors that are suitable for the wall construction.
Fix two suitable screws into the anchors, leaving their heads 3 mm
(0.12 in.) clear of the wall surface. The screws should be at least
30 mm (1.2 in.) long,
Remove any connections in the Switch and locate it over the screw
heads. When in line, gently push the Switch on to the wall and
move it downwards to secure.
Mounting Instructions for Wood Walls
Make two holes 124 mm (4.9 in.) apart.
Fix two suitable screws directly into the wall, leaving their heads
3 mm (0.12 in.) clear of the wall surface. The screws should be at
least 20 mm (0.75 in.) long.
Remove any connections in the Switch and locate it over the screw
heads. When in line, gently push the Switch on to the wall and
move it downwards to secure.
CAUTION: When making connections, be careful not to push the
Switch up and off the wall.
Rear
3
4
3
10BASE-T/100BASE-TX Ports *(Switch 5/Switch 8)
Use suitable TP cable (see Section 3) with RJ-45 connectors.
You can connect your Switch to a workstation, or any
other piece of equipment that has 10BASE-T/ 100BASE-TX
connectivity.
10BASE-T/100BASE-TX/1000BASE-T Ports*
(GIgabit Switch 5/Gigabit Switch 8)
Use suitable TP cable (see Section 3) with RJ-45 connectors.
You can connect your Switch to a workstation, or any
other piece of equipment that has 10BASE-T/100BASE-
TX/1000BASE-T connectivity.
* Each port is capable of autosensing for 10 Mbps, 100
Mbps or 1000 Mbps operation.
All ports have an automatic MDI/MDIX feature, which means
either straight-through or crossover cable can be used to
connect to any port.
Before you Install Your Switch
1
Unit Connections
To connect other units (such as gateways or other switches) to your
Switch you need:
1
One suitable Twisted Pair cable for each workstation.
HP recommends Category 5E or 6 cable for Gigabit connections.
Power Adapter Socket
4
Only use the power adapter that is supplied with the Switch.
2
3
Workstation Connections
To connect workstations or other equipment (such as servers)
directly to your Switch, you need:
1
One suitable Twisted Pair cable for each workstation.
2
One adapter card for each workstation to be connected to
a port on the Switch. The adapter card must be capable
of communicating at the required connection speed. For
example, if you want to use a Gigabit connection, you must
install a 1000BASE-T adapter card.
An operating system (for example, Netware, Windows, MAC
3
or Linux) with network support configured, running on your
workstation.