Diamond Products CC2500 Benutzerhandbuch - Seite 3
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Säge Diamond Products CC2500 herunter. Diamond Products CC2500 10 Seiten.
Seite drucken
SAFETY WARNINGS
PERSONAL SAFETY
• Read
and understand
Instructions before operating
saw.
• Always wear
safety approved
hearing,
eye,
head
and
respiratory protection.
•
Sturdy
boots with nonslip
soles aid
In
providing
proper
footing.
Use of
steel-toed
safety
boots
are
recommended.
• Under certain
conditions,
sparks
may fly
so
never wear
clothes of
flammable material.
•
Know
how to
S,op saw
quickly
in case of emergency.
• Keep all parts of
your
body
away from
blade and all other
moving parts.
• Use caution and follow
Instructions when
loading and
unloading saw.
BLADE SAFETY
• Examine cutting blades before each
use.
Blade should
have
no
cracks, nicks or
flaws.
Center hole should be
undamaged. Use only
the
blades
recommended
for
your
·model.
• This
saw should cut only material
that
Is specified on
each
cutting
blade. Read
the
Instructions
which
are on
each
blade to
determine
which material the blade Is
designed
to
cut.
.
•
Use only reinforced abrasive blades or steel centered
diamond blades manufactured
for use
on concrete saws.
• Inspect blade flanges
for damage, excessive wear and
cleanliness before mounting blade.
Blade
should
fit
snugly on clean, undamaged shaft.
• Use onl}' blades marked
with
a maximum operating speed
greater
than the blade
shaft speed.
·
•
The
ig.
n ltion governor
is designed to
limit
the maximum
engine speed in a no-load condition. Speeds in excess
of
that
may cause
the
blade
to
exceed
the
maximum safe-
allowable
speed.
Do not operate
the
unit
if
.
y ou
suspect
it
of exceeding
this
speed.
·
•
Always keep
guards in place and
do·
not
allow blade
exposure on
the
guard to exceed 180 degrees.
• Avoid getting into
direct
line with the
blade.
• Make
sure
the blade does
not make contact
with the
ground or
any other surface
when transporting the
saw.
GENERAL SAW 'SAFETY
.
•
Saw
must not be left unattended while
the engine
Is
running.
.
• Always remember to keep both hands
on
the
handles
when the
engine
is running.
.
•
Do.not operate
the machine
if
there
Is a
fuel leak. Have
the fuel leak fixed first.
• Use extreme caution and slow speed
when using the
self-propelled drive
to
move
the
saw
up
or
down ramps
or
when loading or unloading from trucks
or
trailers. When
going down
ramps:
DRIVE the
saw forward slowly.
When
going
up
ramps:
BACK the
saw
in reverse
slowly.
CUITING/WORK AREA SAFETY
•
Never operate the saw
In
any appllCl:!tlon or job
where
you are
not
trained or
supervised.
• Operate
.
only In well ventilated
areas.
Engine
exhaust
contains carbon monoxide
which
can cause loss of
consciousness
and possible death.
• Keep bystanders and/or animals out of the
work
area.
• Observe ail safety
regulations for
the safe
handling of
fuel. Handle fuel in
safety containers. Shut off the engine
and allow
it to
cool before
refueling. Wipe
the saw dry
if
fuel
Is spilled on
it. Always move
away
from the fueling
area
before
starting
the
engine.
•
Do not operate
the
saw in areas of combustible material
or
fumes.
Sparks
may
occur
from
saw
that
could cause
a
fire
or an explosion.
Fallure to comply with preceding warnings
could result In serious bodily Injury!
AWARNING:A
The
engine exhaust from this product
·contains chemicals known to the
State of California to cause
cancer,
birth defects or other reproductive harm.
0