Panasonic PT AE700U - High-Definition Home Cinema LCD Projector Betriebsanleitung - Seite 27
Blättern Sie online oder laden Sie pdf Betriebsanleitung für Projektor Panasonic PT AE700U - High-Definition Home Cinema LCD Projector herunter. Panasonic PT AE700U - High-Definition Home Cinema LCD Projector 32 Seiten. Widescreen high definition home cinema projector
Seite drucken
On-screen display
Displayed for 30
seconds. Pressing any
More than 2 700 hours*
button will clear the
display.
Remains displayed until
More than 3 000 hours*
any button is pressed.
* These periods of time may become shorter according to the settings of the projector.
Lamp unit replacement procedure
NOTE:
B If the lamp usage time has passed 3 000 hours (when "LAMP POWER" has been
set to "HIGH" and when "DYNAMIC IRIS" has been set to "ON"), the projector will
switch to standby mode after approximately 30 minutes of operation. The steps
) to - on the next page should thus be completed within 30 minutes.
# Turn off the MAIN POWER
switch according to the
procedure given in "Turning off
the power" on page 26, and
then disconnect the power
cord plug from the wall outlet
and check that the area around
the lamp unit has cooled down.
$ Use a Phillips screwdriver to
turn the lamp unit cover fixing
screws at the bottom of the
projector, and then remove the
lamp unit cover.
Lamp unit cover
Lamp unit cover fixing screws
52-E
NGLISH
LAMP indicator
Illuminates red during
image projection and
standby mode.
% Use a Phillips screwdriver to
loosen the two lamp unit fixing
screws until the screws turn
freely. Then hold the handle of
the lamp unit and gently pull it
out from the projector.
Lamp unit fixing screws
A
B
Handle
& Insert the new lamp unit while
making sure that the direction
of insertion is correct, and then
use a Phillips screwdriver to
securely tighten the lamp unit
fixing screws.
When inserting the new lamp
unit, be sure to push it in at the
point A and B .
' Install the lamp unit cover, and
then use a Phillips screwdriver
to securely tighten the lamp
unit cover fixing screws.
( Insert the power cord plug into
the wall outlet and then press
the MAIN POWER switch.
) Press the POWER button so
that a picture is projected onto
the screen.
* Press the MENU button to
display the "MAIN MENU", and
then press the F or G button
to select "OPTION".
M E N U
K E Y S T O N E
P I C T U R E
P O S I T I O N
S H U T T E R
L A N G U A G E
O P T I O N
SELECT
ENTER
EXIT
+ Press the ENTER button to
display the "OPTION" menu,
and then press the F or G
button to select "LAMP
RUNTIME".
O P T I O N
O S D
O N
N R
O N
C I N E M A R E A L I T Y
O N
B A C K C O L O R
B L U E
W S S
O N
F R O N T / R E A R
F R O N T
D E S K / C E I L I N G
D E S K
F A N C O N T R O L
N O R M A L
L A M P P O W E R
H I G H
L A M P R U N T I M E
2 7 2 0 H
S E L E C T
E S C
, Press and hold the ENTER
button for approximately 3
seconds.
O P T I O N
O S D
O N
N R
O N
C I N E M A R E A L I T Y
O N
B A C K C O L O R
B L U E
W S S
O N
F R O N T / R E A R
F R O N T
D E S K / C E I L I N G
D E S K
F A N C O N T R O L
N O R M A L
L A M P P O W E R
H I G H
T I M E R E S E T [ P O W E R O F F ]
S E L E C T
E S C
The "LAMP RUNTIME" will
change to "TIME RESET
[POWER OFF]".
B If the MENU button is pressed,
the lamp time resetting screen
will be cancelled.
- Turn off the power.
This will reset the cumulative
usage time for the lamp unit to
zero.
Refer to page 26 for details on
how to turn off the power.
NOTE:
B Be sure to install the lamp unit
and the lamp unit cover
securely. If they are not
securely installed, it may cause
the protection circuit to operate
so that the power cannot be
turned on.
E
-53
NGLISH