Panasonic PT-DZ12000U - WUXGA DLP Projector Broschüre & Specs - Seite 6
Blättern Sie online oder laden Sie pdf Broschüre & Specs für Projektor Panasonic PT-DZ12000U - WUXGA DLP Projector herunter. Panasonic PT-DZ12000U - WUXGA DLP Projector 6 Seiten. 3-chip dlp projector
Auch für Panasonic PT-DZ12000U - WUXGA DLP Projector: Handbuch für Einrichtung und Betrieb (37 seiten)
Specifications
Power supply
120–240 V AC 16–9A, 50Hz/60Hz
Power consumption
1,600–1,500 W (10–15 W in standby mode with fan stopped)
DLP
chip
Panel size
0.96" diagonal (16:10 aspect ratio)
®
Display method
DLP
®
chip x 3 (R, G, B), DLP
Pixels
2,304,000 (1,920 x 1,200) x 3, total of 6,912,000 pixels
Lens
Optional powered zoom/focus lenses
Lamp
300 W UHM™ lamp x 4 (four lamp system)
Screen size
70 - 600 inches,16:10 aspect ratio
(70-300 inches, 16:9 aspect ratio with the ET-D75LE5)
Brightness*
12,000 lumens (four-lamp operation mode)
1
Contrast ratio*
1
5,000:1 (full on/full off, in Dynamic iris 3 mode)
Resolution
1,920 x 1,200 pixels
RGB input scanning frequency
f
15-100 kHz, fV 24-120 Hz
H
Dot clock 20-162 MHz
Component signal
480i, 480p, 576i, 576p, 720/60p, 720/50p, 1035/60i, 1080/25p, 1080/24p,
1080/24sF, 1080/30p, 1080/60i, 1080/50i, 1080/50p, 1080/60p
Video signal
f
15.75/15.63 kHz, fV 50/60Hz
H
(NTSC,NTSC4.43,PAL,PAL60,PAL-N,PAL-M,SECAM)
Lens shift
Vertical: ±55% (±44% with the ET-D75LE6) (powered)
Horizontal: ±20% (±15% with the ET-D75LE6) (powered)
Keystone correction range
Vertical: ±40° (±22° with the ET-D75LE5, ±28° with the ET-D75LE6),
Using Geometric Adjustment: Vertical ±10°, Horizontal ±15°
Terminals
DVI-D IN
DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link
480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,
720/60p, 720/50p
VGA (640 x 480) – WUXGA*
Dot clock: 25–162 MHz
RGB1/YP
P
IN
BNC x 5
B
R
RGB2 IN
D-sub HD 15-pin x 1
VIDEO IN
BNC x 1, 1.0 Vp-p
VIDEO OUT
BNC x 1, 1.0 Vp-p
S-VIDEO IN
Mini DIN 4-pin x 1
LAN
RJ-45 (10 Base-T/100 Base-TX) x 1, compatible with PJLink™
SERIAL IN
D-sub 9-pin female x 2 (RS232C x 1, RS422 x 1)
SERIAL OUT
D-sub 9-pin male x 1 (RS422 x 1)
REMOTE 1 IN
M3 jack x1 for wired remote control
REMOTE 1 OUT
M3 jack x1 for link control
REMOTE 2 IN
D-sub 9-pin female x 1 for external control (parallel)
Optional board slot With ET-MD77SD1
SERIAL IN: BNC x 1, SD-SDI signal (YC
installed*
SERIAL OUT: BNC x 1, active through
3
With ET-MD77SD3
SERIAL IN: BNC x 1, SD-SDI signal (YC
installed*
Single-link HD-SDI signal (YC
3
1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
SERIAL OUT: BNC x 1, active through
With ET-MD100SD4
Link A/Link B IN: BNC x 1 for each, SD-SDI signal (YC
installed
Single-link HD-SDI signal (YC
1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE 372M compiant: 1920 x 1080/50i,
1920 x 1080/60i, 1920 x 1080/25p, 1920 x 1080/24p, 1920 x 1080/24sF, 1920 x 1080/30p
Dual-link HD-SDI signal (X'Y'Z' 4:4:4 12-bit): 2048 x 1080/24p, 2048 x 1080/24sF
Projection distance
Diagonal image size
ET-D75LE6
(aspect raio: 16:10)
0.9-1.1:1
min.
max.
1,353 mm
1,615 mm
70"
4.4'
5.3'
1,957 mm
2,339 mm
100"
6.4'
7.7'
2,964 mm
3,546 mm
150"
9.7'
11.6'
3,971 mm
4,752 mm
200"
13.0'
15.6'
5,985 mm
7,165 mm
300"
19.6'
23.5'
7999 mm
9,578 mm
400"
26.2'
31.4'
12,027 mm
14,404 mm
600"
39.5'
47.3'
Diagonal image size
ET-D75LE6
(aspect raio: 16:9)
0.9-1.1:1
min.
max.
1,393 mm
1,662 mm
70"
4.6'
5.4'
2,014 mm
2,406 mm
100"
6.7'
7.8'
3,049 mm
3,646 mm
150"
10.0'
11.9'
4,084 mm
4,886 mm
200"
13.5'
16.0'
6,154 mm
7,366 mm
300"
20.2'
24.1'
8,224 mm
9,846 mm
400"
27.0'
32.2'
12,364 mm
14,806 mm
600"
40.6'
48.5'
NOTES ON USE
1. Do not install the projector in locations that are subject to excessive water, humidity, steam, or oily smoke. Doing so may result in fire,
malfunction, or electric shock.
2. The projector uses a high-voltage mercury lamp that contains high internal pressure. This lamp may break, emitting a large sound, or fail to
illuminate, due to impact or extended use.
3. The projector uses of high-wattage lamp that becomes very hot during operation. Please observe the following precautions.
• Never place objects on top of the projector while it is operation.
• Make sure there is an unobstructed space of 500 mm or more around the projector's exhaust openings.
• Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection.
When stacking projector units, be sure to provide the amount of space indicated between them. These space requirements also apply to
installation where only one projector unit is operating at one time and the other unit is used as a backup.
• If the projector is placed in a box or enclosure, temperature of the air surrounding the projector must be between 0°C and 35°C. Also make sure the
projector's intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked into the intake.
Panasonic Projector Systems Company,
Unit of Panasonic Corporation of North America
www.panasonic.com/projectors
Headquarters
Panasonic Canada Inc.
3 Panasonic Way, 4B-9
5770 Ambler Drive
Secaucus, NJ 07094
Mississauga, Ontario
888-411-1996
Canada L4W 2T3
905 624 5010
®
projection system
2
(1,920 x 1,200), compatible with non-interlaced signals only,
C
4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i
B
R
C
4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i
B
R
C
4:2:2 10-bit): SMPTE 292M compiant: 720/50p, 720/60p,
B
R
C
4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i
B
R
C
4:2:2 10-bit): SMPTE 292M compiant: 720/50p, 720/60p, 1080/50i,
B
R
ET-D75LE1
ET-D75LE2
1.4-1.8:1
1.8-2.8:1
min.
max.
min.
2,013 mm
2,691 mm
2,723 mm
6.6'
8.8'
8.9'
2,908 mm
3,887 mm
3,924 mm
9.5'
12.8'
12.9'
4,401 mm
5,881 mm
5,926 mm
14.4'
19.3'
19.4'
5,893 mm
7,875 mm
7,928 mm
19.3'
25.8'
26.0'
8,877 mm
11,862 mm
11,932 mm
29.1'
38.9'
39.1'
11,862 mm
15,850 mm
15,936 mm
38.9'
52.3'
52.3'
17,831 mm
23,825 mm
23,944 mm
58.5'
78.1'
78.6'
ET-D75LE1
ET-D75LE2
1.4-1.8:1
1.8-2.8:1
min.
max.
min.
2,072 mm
2,768 mm
2,801 mm
6.9'
9.0'
9.2'
2,992 mm
3,998 mm
4,035 mm
9.9'
13.1'
13.3'
4,526 mm
6,047 mm
6,093 mm
14.8'
19.8'
19.9'
6,060 mm
8,096 mm
8,150 mm
19.9'
26.5'
26.8'
9,128 mm
12,194 mm
12,265 mm
30.0'
40.0'
40.3'
12,196 mm
16,292 mm
16,380 mm
40.1'
53.4'
53.8'
18,332 mm
24,488 mm
24,610 mm
60.2'
80.3'
80.8'
R
Optional board slot With ET-MD77DV
Specifications are the same as those for the DVI-D IN terminal on the main unit.
installed
Installation
Front/rear, ceiling/floor
Power cord length
9.9" (3.0 m)
Dimensions (W x H x D)
22-3/4" x 12-19/32" x 25-5/16" (578 x 320 x 643 mm) (without lens)
Weight*
4
Approx. 77.1 lbs (35 kg) without lens
Operating temperature
32 -113 °F (0 -45 °C)*
Operating humidity
10-80% (no condensation)
Supplied accessories
Power cord, Wireless/wired remote control unit,
Batteries for remote control (3V AA battery x2), Eye bolt x4, Wire rope
*
1
Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*
Only when using VESA CVT-RB(Reduced Blanking) signals.
2
*
3
The LAN terminal on each board, when mounted, cannot be used because the LAN terminal on the main unit has priority.
*
Average value. May differ depending on models.
4
*
5
The operating temperature range is 32°F (0°C) to 104°F (40°C) when used in High-Altitude mode (4,593 feet [1,400 m] to 8,858 feet [2,700 m]).
Also, if the ambient temperature exceeds 104°F (40°C) (95°F [35°C] in High-Altitude mode) when using all four lamps, the light output may be
reduced approximately 30% to protect the projector.
Dimensions
22-3/4" (578)
Throw distance
ET-D75LE3
2.8-4.6:1
max.
min.
max.
4,098 mm
4,108 mm
6,900 mm
13.4'
13.5'
22.6'
5,899 mm
5,910 mm
9,909 mm
19.4'
19.4'
32.5'
8,902 mm
8,913 mm
14,924 mm
14,930 mm
29.2'
29.2'
49.0'
11,905 mm
11,916 mm
19,939 mm
19,945 mm
39.1'
39.1'
65.4'
17,911 mm
17,922 mm
29,970 mm
29,975 mm
58.8'
58.8'
98.3'
23,917 mm
23,928 mm
40,000 mm
40,006 mm
78.5'
78.5'
131.2'
35,929 mm
35,939 mm
60,061 mm
60,067 mm
117.9'
117.9'
197.1'
Throw distance
ET-D75LE3
2.8-4.6:1
max.
min.
max.
4,215 mm
4,226 mm
7,094 mm
13.8'
13.9'
23.2'
6,067 mm
6,077 mm
10,187 mm
10,193 mm
19.9'
20.0'
33.4'
9,153 mm
9,164 mm
1,5341 mm
1,5348 mm
30.0'
20.2'
50.3'
12,240 mm
12,250 mm
20,496 mm
20,502 mm
40.1'
40.2'
67.2'
18,413 mm
18,423 mm
30,805 mm
30,811 mm
60.3'
60.5'
101.0'
24,586 mm
24,596 mm
41,114 mm
41,120 mm
80.6'
80.7'
134.8'
36,932 mm
36,942 mm
61,732 mm
61,738 mm
121.1'
121.2'
202.4'
4. If the projector is to be operated continuously 24 hours a day, use the multi-lamp optical system's alternating lamp operation (lamp changer)
function. The projector can be operated continuously 24 hours a day in four-lamp operation mode, but it will automatically operate with three
lamps for 8 hours of the 24 hours.
5. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.
• The length of time that it takes for the lamp to break or fail to illuminate varies greatly depending on individual lamp characteristics and usage
conditions.
• The brightness of the lamp will gradually decrease with use.
6. Because the ET-D75LE5 is a fixed short-throw lens, the lens shift function cannot be used with it.
7. Due to natural characteristics of lamps, screen brightness may vary (flicker). This is not an indication of faulty lamp performance.
For more information about Panasonic projector ––
Please contact Panasonic or your dealer for a demonstration.
(C) 2008 Panasonic Projector Systems Company is a Unit of Panasonic Corporation of North America. All rights reserved.
5
Shape of the plug
unit: inch [mm]
receptacle
•125 V AC, 20 A
•250 V AC, 15 A
ET-D75LE4
ET-D75LE8
4.6-7.4:1
7.3-13.8:1
min.
max.
min.
6,906 mm
11,064 mm
10,780 mm
20,561 mm
22.7'
36.3'
35.4'
9,915 mm
15,849 mm
15,565 mm
29,527 mm
32.5'
52.0'
51.1'
23,824 mm
23,541 mm
44,471 mm
49.0'
78.2'
77.2'
31,799 mm
31,517 mm
59,414 mm
65.4'
104.3'
103.4'
47,749 mm
47,468 mm
89,301 mm
98.3'
156.7'
155.7'
63,699 mm
63,420 mm
119,188 mm
131.2'
209.0'
208.1'
95,599 mm
95,323 mm
178,962 mm
197.1'
313.6'
312.8'
ET-D75LE4
ET-D75LE8
4.6-7.4:1
7.3-13.8:1
min.
max.
min.
7,101 mm
11,374 mm
11,091 mm
21,142 mm
23.3'
37.3'
36.4'
16,292 mm
16,009 mm
30,358 mm
33.5'
53.4'
52.6'
24,488 mm
24,207 mm
45,717 mm
50.3'
80.3'
79.4'
32,685 mm
32,404 mm
61,076 mm
67.3'
107.2'
106.3'
49,078 mm
48,799 mm
91,794 mm
101.1'
160.9'
160.1'
65,471 mm
65,194 mm
122,512 mm
134.9'
214.7'
213.9'
98,257 mm
97,984 mm
183,948 mm
202.6'
322.2'
321.4'
http://panasonic.net/pavc/projector
EC98J2010
JQA-1617
Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product
may be subject to export regulations. UHM is trademark of Matsushita Electric Indusutrial Co., Ltd. VGA and
XGA are trademarks of International Business Machines Corporation. All other trademarks are the property of their
respective trademark owners. Projection Images simulated.
DLP, DLP logo and DLP Medallion logo are trademarks or registered trademarks of Texas Instruments.
The PJLink trademark is an application trademark in Japan, the United States, and other
(C) 2008 Matsushita Electric Industrial Co,Ltd. All rights reserved.
All information included here is valid as of July 2008.
G
W
ET-D75LE5
0.7:1
max.
fixed
992 mm
67.5'
3.3'
1,453 mm
96.9'
4.8'
2,222 mm
145.9'
7.3'
2,991 mm
194.9'
9.8'
4,528 mm
293.0'
14.9'
—
391.0'
—
587.1'
ET-D75LE5
0.7:1
max.
fixed
1,022 mm
69.3'
3.3'
1,496 mm
99.5'
4.9'
2,286 mm
149.9'
7.5'
3,076 mm
200.3'
10.0'
4,656 mm
301.0'
15.2'
—
401.8'
—
603.3'
countries and regions or registered trademarks.
PT-DZ12KU1-08July10K Printed in Japan.