Panasonic PT-L520E Betriebsanleitung - Seite 26
Blättern Sie online oder laden Sie pdf Betriebsanleitung für Projektor Panasonic PT-L520E herunter. Panasonic PT-L520E 30 Seiten. Lcd projector
Seite drucken
On-screen display
Displayed for 30
seconds. Pressing any
More than 1800 hours
button will clear the
display.
This display cannot be
cleared at all, no matter
More than 2000 hours
which button is pressed.
Lamp unit replacement procedure
NOTE:
B If the lamp usage time has passed 2000 hours (when LAMP POWER has
been set to "HIGH"), the projector will switch to standby mode after
approximately 10 minutes of operation. The steps ) to - on the next
page should thus be completed within 10 minutes.
# Turn off the MAIN POWER
switch according to the
procedure given in "Turning off
the power" on page 27, and
then disconnect the power
cord plug from the wall outlet
and check that the area around
the lamp unit has cooled down.
$ Use a Phillips screwdriver to
turn the lamp unit cover fixing
screws at the bottom of the
projector, and then remove the
lamp unit cover from the
projector.
Lamp unit cover
Lamp unit cover fixing screws
50-E
NGLISH
Lamp indicator warning
light
The projector will enter
Standby Mode and the
red indicator lamp will
illuminate.
% Use a Phillips screwdriver to loosen
the two lamp unit fixing screws until
the screws turn freely. Then hold
the handle of the lamp unit and
gently pull it out from the projector.
Lamp unit fixing screws
Handle
& Insert the new lamp unit while
making sure that the direction
of insertion is correct, and then
use a Phillips screwdriver to
securely tighten the lamp unit
fixing screws.
' Install the lamp unit cover, and
then use a Phillips screwdriver
to securely tighten the lamp
unit cover fixing screws.
NOTE:
B Be sure to install the lamp unit
and the lamp unit cover securely.
If they are not securely installed,
it may cause the protection circuit
to operate so that the power
cannot be turned on.
( Insert the power cord plug into
the wall outlet and then press
the MAIN POWER switch.
NOTE:
B If the POWER indicator on the
projector does not illuminate red
when the MAIN POWER switch is
turned on, turn the MAIN POWER
switch off again and check that
the lamp unit and the lamp unit
cover are securely installed. Then
turn the MAIN POWER switch
back on.
) Press the POWER button so
that a picture is projected onto
the screen.
* Press the MENU button to
display the MAIN MENU
screen, and then press the F
and G buttons to move the
cursor to select "OPTION2".
M E N U
K E Y S T O N E
P I C T U R E
P O S I T I O N
I N D E X W I N D O W
S H U T T E R
A U D I O
L A N G U A G E
O P T I O N 1
O P T I O N 2
SELECT
E N T E R
+ Press the ENTER button to
display the OPTION2 screen,
and then use the F and G
buttons to select LAMP
RUNTIME.
O P T I O N 2
B A C K C O L O R
B L U E
F R O N T / R E A R
F R O N T
D E S K / C E I L I N G
D E S K
F A N C O N T R O L
S T A N D A R D
L A M P P O W E R
H I G H
L A M P R U N T I M E
1 8 2 0 H
F U N C 1
I N D E X
C O N T R O L K E Y
O N
S E L E C T
E S C
, Press and hold the ENTER
button for approximately 3
seconds.
O P T I O N 2
B A C K C O L O R
B L U E
F R O N T / R E A R
F R O N T
D E S K / C E I L I N G
D E S K
F A N C O N T R O L
S T A N D A R D
L A M P P O W E R
H I G H
T I M E R E S E T [ P O W E R O F F ]
F U N C 1
I N D E X
C O N T R O L K E Y
O N
S E L E C T
E S C
The "LAMP RUNTIME" will
change to "TIME RESET
[POWER OFF]".
NOTE:
B If the MENU button is pressed,
the lamp time resetting screen
will be cancelled.
- Turn off the power.
This will reset the cumulative
usage time for the lamp unit to
zero.
Refer to page 27 for details on
how to turn off the power.
E
-51
NGLISH