Panasonic SA-AKX220 Betriebsanleitung - Seite 2

Blättern Sie online oder laden Sie pdf Betriebsanleitung für Stereo System Panasonic SA-AKX220 herunter. Panasonic SA-AKX220 2 Seiten. Cd stereo system

Seite drucken

Overview of controls

Do the procedures with the remote control. You can also use the buttons on the main unit if they are the same.

Standby/on switch [`], [1]

View the play menu

Press to switch the unit from on to standby mode or vice

Select the sound effects

versa. In standby mode, the unit is still consuming a

small amount of power.

Remote control sensor

Distance: Within approximately 7 m

Select the audio source

Angle: Approximately 20° up and down, 30° left and right

On the main unit:

To start Bluetooth

pairing, press and hold [

–PAIRING].

Select MP3 album or track

Press [ALBUM/TRACK] to select album or track.

Basic playback control

Browse tracks or albums

Turn [MULTI CONTROL] to browse.

View the setup menu

To start playback from the selection, press [4/9].

View the content information

USB port (

)

Select or confirm the option

USB status indicator

Open or close the disc tray

Display panel

Decrease the brightness of the display panel

Disc tray

To cancel, press the button again.

Select DJ jukebox

Adjust the volume level

Mute the sound

To cancel, press the button again.

"MUTE" is also cancelled when you adjust the volume or

when you switch off the system.

Preparing media

Disc

Press [CD x] (main unit: [x OPEN/CLOSE]) to open the disc tray.

Put in a disc with the label facing up.

Press again to close the disc tray.

Press [USB/CD] to select "CD".

USB

Preparation

Before you connect a USB device to the system, make sure you do a backup of the data.

Decrease the volume and connect the USB device to the USB port.

Hold the main unit when connecting or disconnecting the USB device.

Press [USB/CD] to select "USB A" or "USB B".

USB status indicator lights up in red when selected.

Note:

Do not use a USB extension cable. The system cannot recognise USB device connected through a cable.

Bluetooth

You can connect and play an audio device wirelessly through Bluetooth

Preparation

• Switch on the Bluetooth

feature of the device and put the device near the system.

• Read the operating instructions of the device for details.

Pairing a device

Connecting a device

Preparation

If this system is connected to a Bluetooth

device,

If this system is connected to a Bluetooth

disconnect it (Z"Disconnecting a device").

Press [ ].

If "PAIRING" is shown, continue with step 3.

"BLUETOOTH READY" is shown.

Press [PLAY MENU] to select "PAIRING" and then

Select "SC-AKX220" from the Bluetooth

press [OK].

the device.

The name of the connected device is shown for a few

Select "SC-AKX220" from the Bluetooth

menu of

seconds.

the device.

Start playback on the device.

If prompted for a passkey, input "0000".

The device connects with this system automatically after

Note:

pairing is complete.

•

A device must be paired to connect.

The name of the connected device is shown for a few

•

This system can only connect to one device at a time.

seconds.

•

When "BLUETOOTH" is selected as the source, this system

Using the main unit

will automatically try to connect to the last connected device.

("LINKING" is shown during this process.)

Press and hold [

–PAIRING] until "PAIRING" is

shown.

Disconnecting a device

Select "SC-AKX220" from the Bluetooth

menu of

Press [ ].

the device.

Note:

Press [PLAY MENU] to select "DISCONNECT?".

You can pair up to 8 devices with this system. If a 9th device is

Press [R, T] to select "OK? YES" and then press

paired, the device that has not been used for the longest time will

be replaced.

[OK].

"BLUETOOTH READY" is shown.

To cancel, select "OK? NO".

Using the main unit

Press and hold [

–PAIRING] until "PAIRING" is shown.

Note:

A device is disconnected when you:

•

Select a different source.

•

Move the device out of the maximum range.

•

Disable the Bluetooth

transmission of the device.

•

Switch off the system or the device.

Media playback

Radio

The following marks indicate the availability of the feature.

Preparation

Press [RADIO/AUX] to select "FM" or "AM".

CD-R/RW in CD-DA format or with MP3 files.

USB device with MP3 files.

USB

BLUETOOTH

Bluetooth

device.

Manual tuning

Basic playback

Press [PLAY MENU] to select "TUNE MODE".

Press [R, T] to select "MANUAL" and then press

CD USB BLUETOOTH

[OK].

Play

Press [4/9].

Press [2/3] or [5/6] to tune in to the

Stop

Press [8].

station.

USB

To tune automatically, press and hold the button until

The position is memorised.

the frequency starts changing quickly.

"RESUME" is shown.

"STEREO" is shown when a stereo broadcast is being

Press again to stop fully.

received.

Pause

Press [4/9].

Using the main unit

Press again to continue playback.

Press [TUNE MODE] to select "MANUAL".

Skip

Press [2/3] or [5/6] to skip track.

CD USB

Press [2/3] or [5/6] to tune in to the

Press [R, T] to skip MP3 album.

station.

Press and hold [2/3] or [5/6].

Note:

Memory presetting

Depending on the Bluetooth

device, some operations may not

work.

You can preset up to 30 FM and 15 AM stations.

Automatic presetting

Viewing available information

Press [PLAY MENU] to select "A.PRESET".

CD USB BLUETOOTH

Press [R, T] to select "LOWEST" or "CURRENT" and

You can view the available information, such as MP3 album

and track number, on the display panel.

then press [OK].

Press [DISPLAY].

LOWEST

Note:

CURRENT

•

Maximum characters that can be shown: Approximately 32

The tuner presets all the stations it can receive into the

•

This system supports ver. 1.0, 1.1 and 2.3 ID3 tags.

•

channels in ascending order.

Text data that the system does not support can show

To cancel, press [8].

differently.

Manual presetting

Play menu

Press [PLAY MENU] to select "TUNE MODE".

CD USB

Press [R, T] to select "MANUAL" and then press

[OK].

Press [PLAY MENU].

Press [2/3] or [5/6] to tune in to the

USB

station.

Press [PLAY MENU] to select "PLAYMODE".

Press [R, T] to select the setting and then press

Press [OK].

[OK].

Press [R, T] to select a preset number and then

OFF

Cancel the setting.

press [OK].

Do steps 3 through 5 again to preset more stations.

PLAYMODE

The new station replaces any station that occupies the

1-TRACK

Play one selected track.

same preset number.

Press [2/3] or [5/6] to select

the track.

Selecting a preset station

1-ALBUM

Play one selected MP3 album.

Press [R, T] to select the MP3 album.

Press [PLAY MENU] to select "TUNE MODE".

RANDOM

Play all tracks randomly.

Press [R, T] to select "PRESET" and then press

RND

[OK].

1-ALBUM

Play all tracks in one selected MP3

RANDOM

album randomly.

Press [2/3] or [5/6] to select the preset

Press [R, T] to select the MP3 album.

station.

RND

ALL REPEAT

Repeat all tracks.

Using the main unit

Press [TUNE MODE] to select "PRESET".

1-TRACK

Repeat 1-TRACK.

REPEAT

Press [2/3] or [5/6] to select the preset

station.

1-ALBUM

Repeat 1-ALBUM.

REPEAT

Improving the sound quality

RANDOM

Repeat random playback.

When "FM" is selected

REPEAT

Press [PLAY MENU] to select "FM MODE".

RND

Press [R, T] to select "MONO" and then press [OK].

1-ALBUM

Repeat 1-ALBUM RANDOM.

RANDOM

To cancel, select "STEREO".

REPEAT

"MONO" is also cancelled when you change the

frequency.

RND

To memorise the setting

Note:

Continue with step 4 of "Manual presetting".

device,

•

During random playback, you cannot skip to tracks which

have been played.

When "AM" is selected

•

The setting is cancelled when you open the disc tray or

Press [PLAY MENU] to select "B.PROOF".

disconnect the USB device.

Press [R, T] to select the setting that provides the

best reception and then press [OK].

menu of

Link mode

BLUETOOTH

Checking the signal status

You can change the link mode to suit the connection type.

When "FM" is selected

Preparation

Press [DISPLAY].

If this system is connected to a Bluetooth

device,

disconnect it (Z"Disconnecting a device").

FM – – – –

Press [PLAY MENU] to select "LINK MODE".

FM ST

Press [R, T] to select the mode and then press [OK].

FM MONO

MODE 1

Emphasis on connectivity.

MODE 2 (default)

Emphasis on sound quality.

AM allocation setting

Note:

By main unit only

•

Depending on the device, the playback image and sound may

not be synchronised. In this case, select "MODE 1".

This system can also receive AM broadcasts allocated in

•

10 kHz steps.

Select "MODE 1" if the sound is interrupted.

Press [RADIO/AUX] to select "FM" or "AM".

Press and hold [RADIO/AUX].

After a few seconds, the display panel shows the current

minimum radio frequency. Release the button when the

minimum frequency changes.

• To go back to the initial setting, do the above steps again.

• Preset frequencies are erased after you change the

setting.

Sound effects

Preset EQ

Press [SOUND] (main unit: [LOCAL EQ]) to select

"PRESET EQ".

Press [R, T] to select the desired preset EQ setting

and then press [OK].

Or turn [MULTI CONTROL] to select the desired preset

EQ setting.

Manual EQ

Press [SOUND] (main unit: [LOCAL EQ]) to select

"MANUAL EQ".

Press [R, T] to select the sound effect.

Or turn [MULTI CONTROL] to select the sound effect.

Press [2/3] or [5/6] to select the setting

and then press [OK].

BASS/MID/TREBLE –4 to +4

SURROUND

"ON SURROUND" or

"OFF SURROUND"

D.Bass

Press [SOUND] to select "D.BASS" and then press

[R, T] to select "D.BASS LEVEL" or "D.BASS BEAT".

Or press [D.BASS] on the main unit to select

"D.BASS LEVEL" or "D.BASS BEAT".

To cancel, select "OFF D.BASS".

Press [2/3] or [5/6] to select the setting

and then press [OK].

Or turn [MULTI CONTROL] to select the setting.

Note:

D.BASS BEAT: This function emphasises the attack level of the

Tuning begins from the lowest frequency.

drumbeat and produces a punchy sound. Depending on the

Tuning begins from the current frequency.

track, the effect may be small.

DJ jukebox

USB

You can use DJ jukebox to add cross-fading effect between

songs. You can also use additional features with the

"Panasonic MAX Juke" app (Zbelow).

Press [PLAY MENU] to select "JUKEBOX".

Press [R, T] to select the setting and then press

[OK].

Using the main unit

Press [DJ JUKEBOX] to select the setting.

OFF CROSSFADE

Cancel cross-fading.

ON CROSSFADE

Add cross-fading.

OFF

Switch off DJ jukebox.

Changing the repeat setting

Press [PLAY MENU] to select "PLAYMODE".

Press [R, T] to select the setting and then press

[OK].

Using the main unit

In the stop mode, turn [MULTI CONTROL] to select the

setting and then press [4/9].

RANDOM REPEAT

Repeat random playback.

RND

ALL TITLE REPEAT

Repeat all tracks.

Note:

•

The system switches to repeat mode automatically when you

switch on DJ jukebox.

•

DJ jukebox is switched off when you switch off the system or

change to another source.

Using the "Panasonic MAX Juke" app

You can download and install the free Android™ app

"Panasonic MAX Juke" on Google Play™ for additional

features, such as to request song playback from multiple

devices simultaneously. You can also call up the tracks

you want to play through the app. For details on the app,

refer to the site below.

http://av.jpn.support.panasonic.com/support/global/cs/audio/

app/max_juke/android/index.html

(This site is in English only.)

External equipment

You can connect a VCR, DVD player etc. and listen to the

audio through this system.

Preparation

• Disconnect the AC mains lead.

• Switch off all equipment and read the appropriate

The FM signal is in monaural.

operating instructions.

The system is not tuned in to a station.

DVD player (not supplied)

The FM signal is in stereo.

"MONO" is selected as the "FM MODE".

Rear panel of

this main unit

Audio cable

(not supplied)

Connect the external equipment.

Press [RADIO/AUX] to select "AUX".

Play the external equipment.

To adjust the input level

Press [PLAY MENU] to select "INPUT LEVEL".

Press [R, T] to select "NORMAL" or "HIGH" and

then press [OK].

Note:

•

Select "NORMAL" if the sound is distorted during "HIGH"

input level.

•

Components and cables are sold separately.

•

If you want to connect equipment other than those described,

refer to the audio dealer.

•

Sound distortion can occur when you use an adaptor.

Clock and timers

Troubleshooting

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions

Setting the clock

indicated do not solve the problem, consult your dealer for instructions.

Common problems

This is a 24-hour clock.

Press [SETUP] to select "CLOCK".

The unit does not work.

•

The safety device has been activated. Do the following:

Press [R, T] to set the time and then press [OK].

Press [1] on the main unit to switch the unit to standby

mode. If the unit does not switch to standby mode,

To check the time

–

Press and hold the button for a minimum of 10 seconds.

Press [SETUP] to select "CLOCK" and then press [OK].

Or,

In standby mode, press [DISPLAY].

–

Disconnect the AC mains lead and then connect it again.

Press [1] again to switch on the unit. If the problem

Note:

persists, consult your dealer.

Reset the clock regularly to maintain accuracy.

The display panel lights up and changes continuously in

standby mode.

Sleep timer

•

Press and hold [8] on the main unit to select "DEMO OFF".

No operations can be done with the remote control.

The sleep timer switches off the system after the set time.

•

Examine that the battery is installed correctly.

Press [SETUP] to select "SLEEP".

Sound is distorted or no sound.

Press [R, T] to select the setting (in minutes) and

•

Adjust the volume of the system.

•

Switch off the system, determine and correct the cause, and

then press [OK].

then switch on again. It can be caused by straining of the

To cancel, select "OFF".

speakers through excessive volume or power, and when using

the system in a hot environment.

A humming sound can be heard during playback.

•

An AC mains lead or fluorescent light is near the cables. Keep

Note:

other appliances and cords away from the cables of this

•

The remaining time is shown for a few seconds every minute.

system.

"SLEEP 1" is always shown when only 1 minute remains.

The sound level reduces.

•

The play timer and sleep timer can be used together.

•

The protection circuit has been activated due to the

•

The sleep timer always comes first. Be sure not to set an

continuous use at high volume output. This is to protect the

overlap of timers.

system and maintain the sound quality.

Play timer

Disc

(Except for Bluetooth

and AUX source)

Display not shown correctly.

Playback does not start.

You can set the timer to come on at a certain time to wake

•

You have not put in the disc correctly. Put it in correctly.

you up.

•

Disc is dirty. Clean the disc.

Preparation

•

Replace the disc if it is scratched, warped, or non-standard.

Set the clock.

•

There is condensation. Let the system dry for 1 to 2 hours.

Press [SETUP] to select "TIMER ADJ".

The total number of tracks displayed is incorrect.

The disc cannot be read.

Press [R, T] to set start time and then press [OK].

Distorted sound is heard.

•

You put in a disc that the system cannot play. Change to a

Do step 2 again to set the end time.

playable disc.

•

You put in a disc that has not been finalised.

Press [R, T] to select the source you want to play

and then press [OK].

USB

To start the timer

The USB device or the contents in it cannot be read.

Press [SETUP] to select "TIMER SET".

•

The format of the USB device or the contents in it are not

compatible with the system.

Press [R, T] to select "PLAY ON" and then press

•

USB devices with storage capacity of more than 32 GB cannot

[OK].

work in some conditions.

"#" is shown.

Slow operation of the USB device.

To cancel, select "PLAY OFF".

•

Large content size or large memory USB device takes longer

The system must be switched off for the timer to

time to read.

operate.

To check the setting

Bluetooth

Press [SETUP] to select "TIMER ADJ" and then press

Pairing cannot be done.

[OK].

•

Check the Bluetooth

device condition.

In standby mode, press [DISPLAY] two times.

•

The device is out of the 10 m communication range. Move the

Note:

device nearer to the system.

•

The timer starts at a low volume and increases gradually to the

The device cannot be connected.

preset level.

•

The pairing of the device was unsuccessful. Do pairing again.

•

The timer comes on at the set time every day if the timer is on.

•

The pairing of the device has been replaced. Do pairing again.

•

If you switch off the system and then switch on again while a

•

This system might be connected to a different device.

timer is in operation, the timer will not stop at the end time.

Disconnect the other device and try pairing the device again.

•

The system may have a problem. Switch off the system and

then switch on again.

The device is connected but audio cannot be heard through

the system.

•

For some built-in Bluetooth

devices, you have to set the

audio output to "SC-AKX220" manually. Read the operating

instructions of the device for details.

Sound from the device is interrupted.

•

The device is out of the 10 m communication range. Move the

device nearer to the system.

•

Remove any obstacle between the system and the device.

•

Other devices that use the 2.4 GHz frequency band (wireless

router, microwaves, cordless phones, etc.) are interfering.

Move the device nearer to the system and distance it from the

other devices.

•

Select "MODE 1" for stable communication.

Radio

Sound is distorted.

Others

•

Use an optional FM outdoor antenna. The antenna should be

installed by a competent technician.

A beat sound is heard.

Auto off

•

Switch off the TV or move it away from the system.

•

Move mobile telephones away from the system if the

This system automatically switches off when you do not use

interference is apparent.

it for approximately 20 minutes.

•

When in AM tuner mode, select the "B.PROOF" setting that

provides the best reception.

Press [SETUP] to select "AUTO OFF".

A low hum is heard during AM broadcasts.

Press [R, T] to select "ON" and then press [OK].

•

Move the antenna away from other cables and cords.

To cancel, select "OFF".

Note:

This function does not work when you are in radio source or

when a Bluetooth

device is connected.

Bluetooth

standby

This function automatically switches on the system when

you establish a Bluetooth

connection from a paired device.

Press [SETUP] to select "BLUETOOTH STANDBY".

Press [R, T] to select "ON" and then press [OK].

To cancel, select "OFF".

Note:

Some devices may take longer to respond. If you are connected

to a Bluetooth

device before switching off the system, wait for a

minimum of 5 seconds before connecting to this system from

your Bluetooth

device again.

Software version

You can check the software version of the system.

Press [SETUP] to select "SW VER." and then press

[OK].

The software version is shown.

Press [OK] again to exit.

Main unit displays

"ADJUST CLOCK"

•

The clock is not set. Adjust the clock.

"ADJUST TIMER"

•

The play timer is not set. Adjust the play timer.

"AUTO OFF"

•

The system has not been used for 20 minutes and will switch

off within a minute. To cancel, press any button.

"ERROR"

•

An incorrect operation was done. Read the instructions and try

again.

"F61"

•

Examine and correct the speaker cords connection.

•

Disconnect the USB device. Switch off the system and then

switch on again.

"F703"

•

Examine the Bluetooth

connection.

•

Disconnect the Bluetooth

device. Switch off the system and

then switch on again.

"F76"

•

There is a problem with the power supply.

•

Disconnect the AC mains lead and consult your dealer.

"F77"

•

Disconnect the AC mains lead and consult your dealer.

"NO DISC"

•

You have not put in a disc.

"NO PLAY"

"UNSUPPORT"

•

Examine the content. You can only play supported format.

•

The system may have a problem. Switch off the system and

then switch on again.

"NO TRACK"

•

There is no album or track in the USB device.

"PLAYERROR"

•

An unsupported MP3 file has been played. The system will

skip that track and play the next one.

"REMOTE 1"

"REMOTE 2"

•

The remote control and the main unit are using different

codes. Change the code of the remote control.

–

When "REMOTE 1" is shown, press and hold [OK] and [ ]

for a minimum of 4 seconds.

–

When "REMOTE 2" is shown, press and hold [OK] and

[USB/CD] for a minimum of 4 seconds.

"TEMP NG"

•

The temperature protection circuit has been activated, and the

system will switch off. Let the unit cool down before switching

it on again.

•

Check that the ventilation opening of the unit is not

obstructed.

•

Ensure this unit is well ventilated.

"USB A NO DEVICE"

"USB B NO DEVICE"

•

The USB device is not connected. Examine the connection.

"USB OVER CURRENT ERROR"

•

The USB device is using too much power. Disconnect the

USB device, switch off the system and then switch on again.

"VBR"

•

The system cannot show the remaining play time for variable

bit rate (VBR) tracks.

Remote control code

When other Panasonic equipment responds to the remote

control of this system, change the remote control code for

this system.

Preparation

Press [USB/CD] to select "CD".

To set the code to "REMOTE 2"

Press and hold [USB/CD] on the main unit and

[USB/CD] on the remote control until "REMOTE 2" is

shown.

Press and hold [OK] and [USB/CD] on the remote

control for a minimum of 4 seconds.

To set the code to "REMOTE 1"

Press and hold [USB/CD] on the main unit and [ ] on

the remote control until "REMOTE 1" is shown.

Press and hold [OK] and [ ] for a minimum of

4 seconds.

System memory reset

Reset the memory when the following situations occur:

• There is no response when buttons are pressed.

• You want to clear and reset the memory contents.

Disconnect the AC mains lead.

While you press and hold [1] on the main unit,

connect the AC mains lead again.

Continue to press and hold the button until

"– – – – – – – – –" is shown.

Release [1].

All the settings are set back to the factory preset.

It is necessary to set the memory items again.