3Com 3C16701 - OfficeConnect 8/TPC Hub Installationshandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Installationshandbuch für Schalter 3Com 3C16701 - OfficeConnect 8/TPC Hub herunter. 3Com 3C16701 - OfficeConnect 8/TPC Hub 2 Seiten. With gigabit uplink

Seite drucken

1 POSITIONING YOUR SWITCH

Safety Information

WARNING: Please read the 'Important Safety Information' section in

the Support and Safety Information sheet before you start.

VORSICHT: Bitte lesen Sie den Abschnitt 'Wichtige

Sicherheitsinformationen' sorgfältig durch, bevor Sie das Gerät einschalten.

AVERTISSEMENT: Veuillez lire attentivement la section "Consignes

importantes de sécurité" avant de mettre en route.

When positioning your Switch, ensure:

• It is out of direct sunlight and away from sources of heat.

• Cabling is away from power lines, fluorescent lighting fixtures, and

sources of electrical noise such as radios, transmitters and broadband

amplifiers.

• Water or moisture cannot enter the case of the unit.

• Air flow around the unit and through the vents in the side of the case is

not restricted. 3Com recommends you provide a minimum of 25 mm

(1 in.) clearance.

Using the Rubber Feet

Use the four self-adhesive rubber feet to prevent your Switch from moving

around on your desk, or when stacking with flat top OfficeConnect units.

Only stick the feet to the marked areas at each corner on the underside of

your Switch.

Using a Stacking Clip

Use a stacking clip when stacking your Switch with other curved

OfficeConnect units. The stacking clip allows you to stack units neatly and

securely.

CAUTION: You can stack up to a maximum of four units. Smaller units

must be stacked above larger units.

3 CONNECTING WORKSTATIONS

Twisted Pair (TP) Cables

Cables can be shielded (screened) or unshielded. Cables must be Category

5 or above. 3Com recommends Category 5E cable for Gigabit connections.

The maximum length you can use is 100 m (328 ft).

Twisted Pair (TP) cable is very easy to use. To connect a TP cable, simply

slot the connector into the relevant RJ-45 Port. When a connector is fully

in, its latch locks into place. To disconnect the cable, push the connector's

latch in and remove it.

When one end of a TP cable is connected to the Switch and the other end

is connected to the network interface card of a workstation or other

device, the Switch will automatically detect whether a straight-through or

crossover cable is being used and will compensate if required. The units

will then autonegotiate to determine the fastest possible link speed

between them. This may take a few seconds and the outcome will be

reflected in the LEDs on the front of the Switch.

If the equipment connected to the Switch does not support autonegotiation

or it has been disabled, it must be configured to operate in half duplex mode.

Expanding Your Network

You can increase the number of workstations and other devices that can

connect to your network by adding OfficeConnect products. You can

connect a 10BASE-T or 100BASE-TX OfficeConnect unit to each port of the

Switch, or a 10BASE-T/100BASE-TX/1000BASE-T OfficeConnect unit to the

Gigabit Port of the Switch.

The Switch has automatic MDI/MDIX functionality, and therefore does not

require the Uplink/Normal switch associated with some OfficeConnect

products. Simply plug in the cable, and the Switch will automatically detect

which wiring practice has been followed, and will compensate accordingly.

Checking Unit Connections

When you have connected all your units, power on the units and the

Switch. The Port Status LEDs for the ports you have used should be lit. If

they are not, check your connections.

To fit the clip:

1 Fit the clip across the top of the unit, as shown in Figure 2 (picture 1),

ensuring that the longer sections of the fastening pieces are pointing

downwards.

2 Align the fastening pieces over the slots found on each side of the unit.

3 Push the clip down gently to secure it, ensuring that the fastening pieces

snap into the slots on the unit.

To fit another unit:

1 Rest the second unit on the top of the clip and align it with the front of

the unit below.

2 Press down gently on the unit to secure it onto the clip, ensuring the

fastening pieces fit into the slots on the unit below, as shown in Figure 2

(picture 2).

Fastening

Piece

Fastening

Piece

Figure 2 Stacking Your Units together

4 HOW YOUR SWITCH CAN BE USED

Switching

When a network of repeater hubs is in operation, any information that is sent

by the workstation is passed around the whole network (regardless of the

destination of the information). This can result in a lot of unnecessary traffic that

can slow the network down. The Switch solves this problem because it "listens"

to the network and automatically learns what workstations can be reached

through its ports. It can then selectively pass on any information by transmitting

the traffic from the relevant port only. This operation is called "switching".

The Switch effectively divides up your network, localizing the network traffic and

passing on traffic as necessary. If you have any high performance workstations

that require a lot of bandwidth, connect them directly to the Switch.

Traffic Prioritization

The Switch has a built in feature to aid network performance at times of

excessive load. It is called Priority Queuing. When a packet is received, the Switch

will examine it to see if it has been priority encoded. If it has, the Switch will then

read the priority level and determine whether it should be directed through the

normal or high priority channel. This feature can be useful during excessive

loads, for example, when one type of traffic may require priority over another.

Connecting 10BASE-T and 100BASE-TX Networks

The 10/100 ports can each be connected to either a 10BASE-T or 100BASE-TX

network. If you have both types of network, you can join them together using

the Switch allowing all your workstations to communicate. Alternatively, if you

use 10BASE-T and want to improve network performance by introducing

100BASE-TX technology, the Switch protects the investment in your existing

workstations because it maintains 10BASE-T connections to them.

Connecting 1000BASE-T Networks

The Gigabit port can be connected to a 10BASE-T/100BASE-TX/1000BASE-T

device, such as a workstation or a server. By connecting the Gigabit port to a

server, all the workstations connected to the server can communicate with devices

connected to the Switch, significantly increasing the size of your network.

Wall Mounting

There are two slots on the underside of the Switch that can be used for wall

mounting. The Switch must be mounted with the LEDs facing upwards.

When wall mounting the unit, ensure that it is within reach of the

power outlet.

When wall mounting the unit, ensure that the rubber feet are not

fixed.

You need two suitable screws. Ensure that the wall you are going to use is

smooth, flat, dry and sturdy. Make two screw holes 150 mm (5.9 in.) apart.

Fix the screws into the wall, leaving their heads 3 mm (0.12 in.) clear of the

wall surface.

Remove any connections in the Switch and locate it over the screw heads.

When in line, gently push the Switch on to the wall and move it downwards

to secure. When making connections, be careful not to push the Switch up

and off the wall.

CAUTION: Only wall mount single units, do not wall mount stacked

units.

5 PROBLEM SOLVING

The Switch has been designed to aid you when detecting and solving

possible problems with your network. These problems are rarely serious; the

cause is usually a disconnected or damaged cable, or incorrect configu-

ration. If this section does not solve your problem, contact your supplier for

information on what to do next.

Perform these actions first:

• Ensure all network equipment is powered on.

• Power each piece of network equipment off, wait about five seconds and

then power each one on.

CAUTION: Do not power the Switch off and then immediately on.

Wait about five seconds between power cycles.

Check the following symptoms and solutions:

Power Status LED or Power Adapter OK LED not lit. Refer to the

following table.

Power Adapter OK LED Power Status LED Problem and Action

All functioning correctly

Off

The internal power supply has

failed.

Contact 3Com Technical Support

for a replacement Switch.

Off

The power adapter or power

adapter connection is faulty.

Refer to "Replacement Power

Adapters" below.

Replacement Power Adapters

If both the Power Adapter OK LED and Power Status LED are off, check your

power adapter connection. If there is still no power, contact 3Com Technical

2 BEFORE YOU INSTALL YOUR SWITCH

Unit Connections

To connect OfficeConnect units (such as gateways or other switches) to

your Switch you need:

• One suitable Twisted Pair (TP) cable for each unit

3Com recommends Category 5E cable for Gigabit connections.

Workstation Connections

To connect workstations or other equipment (such as servers) directly to

your Switch, you need:

1 Either:

• One 10BASE-T, 100BASE-TX or 10/100BASE-TX adapter card for each

workstation to be connected to a 10/100 Port on the Switch, or

• One 1000BASE-T adapter card for each workstation or other device

to be connected to the Gigabit port on the Switch.

3Com produce a range of easy to install network adapter cards.

2 An operating system (for example Netware or Windows 95/98/Me/2000/

XP) with network support configured, running on your workstations.

3 One suitable Twisted Pair cable for each workstation.

Figure 3 Workstation connections

Support and ask for a replacement power adapter. Please quote the power

adapter part number, shown on the OfficeConnect power adapter you are

currently using.

Alternatively, quote the part number for your region:

Part number

Region

3C16740A

US and Canada

3C16741A

3C16742A

Europe and Middle East

3C16743A

Japan

3C16744A

Australasia (except Japan and Korea)

3C16745A

South Africa

3C16747A

Korea

Only use the power adapter supplied with the Switch or a

replacement OfficeConnect power adapter. Do not use any other

power adapter.

Port Status LED not lit for a port that has a TP cable connected. After

connection, it may take several seconds for the Port Status LEDs to

illuminate. The Port Status LED should turn Green, Yellow or Blue for each

port that is connected, depending on connection speed. The Duplex LED

may or may not illuminate. Please refer to 'About Your Switch' for a full

description of the LEDs.

If the Port Status LED is not lit after several seconds, ensure that the

connected device is powered on, that the TP cable is not damaged and that

it is correctly inserted at both ends.

You may find that a TP cable works when connected to the Switch, but that

it does not if disconnected from the Switch and connected to another

device. This may be because the other device does not have the automatic

MDI/MDIX feature.