EasyPro LSF12K Gebrauchsanweisung

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Außen-Brunnen EasyPro LSF12K herunter. EasyPro LSF12K 2 Seiten. Arching stream fountains

Seite drucken

Thank you for purchasing the Arching Stream Fountain, a color-changing LED light stream that adds beauty, fun and enjoyment

to any water feature, pond, fountain or pool.

Specifications

• Inlet —

" mpt

• Nozzle — 17mm

• Electrical Requirement — LED operated on a AC 12 volt power adapter, transformer included

• LED Light — 3 x 3 watts multi color

• Ideal Installation — 6-10 feet spray distance with 5-6 feet max arch height

NOTE: Further distance and higher arch can be achieved if installed indoor with no wind. Avoid using in windy locations.

General Information and Operation

Please read the following before installing or running the Arching Stream Fountain.

1. The Arching Stream Fountain must be used in a clean water environment. If the water is dirty a pre-filter is required. Running

dirty water through the fountain will result in improper flow and disrupted stream.

2. Flow rates between 600-1000 gph are recommended. The flow consistency of mag drive pumps best suit the functionality of

the Arching Stream Fountain. Avoid pumps with inconsistent flow.

3. The nozzle of the Arching Stream Fountain should never be submersed. The fountain can be submersed into the water as

long as the nozzle remains above water.

4. Avoid using elbows at the inlet of the fountain. An elbow can cause distortion in pump pressure and flow.

5. A flow control valve is recommended to adjust water flow and size of the arch. Install ball valve in line between the pump

and fountain. If the arch is too long it will result in a disrupted stream and may cause splashing. Windy locations may limit

the distance that an uninterrupted stream is able to travel. Ideal applications will be able to maintain the arch to a maximum

length of 12 feet.

NOTE: You may need to adjust the length of the arch to be sure the light can travel from start to end. If arch is too long the

light may not reach the end and the stream flow could get distorted.

6. Periodic maintenance is required for proper flow of water and light. Please see maintenance instructions to clean the LED light

lens and filter sponges inside the fountain.

7. Transformer is not submersible. Turn the LED light on only when water is running.

NOTE: If the fountain is not properly filled with water it will cause the stream to distort and splatter. To fix this simply tilt the

nozzle 15-20 degrees forward and return it back to desired angle. If noise is coming out of the unit do the same. At times you

may have to tilt the nozzle 15 degrees in the opposite direction then back to normal to purge air from the unit.

Installation with Kit (LSF12K, LSF12LK)

Each kit includes the components needed for the full operation of a single Arching Stream Fountain. Additional parts may be

required for unique applications.

1. Determine installation location. Before gluing, dry fit flex pipe and fittings together and adjust placement as necessary.

2. Secure flex pipe and fittings together using PVC glue.

3. Once glue is completely dry, submerse EP850 pump into pool or pond. The pump must remain submersed at all times.

4. Plug pump in; adjust the angle of the main body and the ball valve to achieve the desired look of the fountain.

Remote Control Operation

• Remote control operates unit up to 10 feet away. Battery strength and direct line of sight may affect remote range.

• In order to operate Arching Stream Fountain with remote control you must purchase units that are sold with a remote control

(LSF12L, LSF12LK) at initial purchase.

NOTE: LSF12 and LSF12K are not capable of remote operation and cannot be upgraded.

• CR2025 battery included

LSF12 • LSF12L • LSF12K • LSF12LK

Arching Stream Fountains

Instructions for Use • Maintenance Guide

Distributed by: EasyPro Pond Products, Grant, MI • easypropondproducts.com