Alpha Communications ART4LITE/G2 Kurzanleitung - Seite 2

Blättern Sie online oder laden Sie pdf Kurzanleitung für Intercom System Alpha Communications ART4LITE/G2 herunter. Alpha Communications ART4LITE/G2 2 Seiten. Monitor

Seite drucken
ART4LITE/G2 MONITOR
SAFETY PRECAUTIONS
-
Always disconnect the power supply
before installing or making modifications to the device.
.
- The fitting and handling of these devices must be carried out by
- The wiring must run at least 15.75" (40 cm.) away from any other wiring.
.
- Do not over tighten the screws on the connector.
- Install the monitor in a dry protected location free from the risk of dripping or splashing water.
- Do not place in humid, dusty or smoky locations, or near sources of heat.
- Before connecting the device to the mains, check the connections between the door panel, power
supply, distributors and monitors.
- Always follow the instructions contained in this manual.
( )
CHARACTERISTICS
*
- Hands-free monitor.
- 4.3" TFT color screen.
.
-
Function push buttons
for access and selection of menu function.
- Monitor
with simple installation (non-polarised 2 wires bus)
.User
-
User menu
.
.
-
Installer menu
.
.
-
Image and communication settings menu
.
-
Output auxiliary call repeater (max.
50mA/12V ).
.
- "HZ" input for calls from apartment front door.
.
- Push buttons for door release 1 and 2.
.
-
Notification l
eds.
.
-
Configuration switches to assign the
call
address
- Function codes to define whether the monitor is master or slave (default: master).
( )
SYSTEM OPERATION
*
- To make a call, the visitor must press the button of the apartment; an audible sound indicates that the call
is being made and
door panel
LED
will turn on. If vocal synthesis is enabled, a 'Call is in progress'
message appears indicating that a call is being made. At this moment, the apartment's monitors receive
the call. If another apartment is called by mistake, press the button for the correct apartment and the first
call will be cancelled.
.
- Upon receiving the call, the image will appear on the screen of the master monitor (and slave 1, if it
exists) without the visitor knowing and icon
image from slave monitors 2 or 3, press
one of the buttons of the monitor to display the image
call is not answered within 45 seconds,
door panel
.
- To establish communication, press
the button below
panel LED
will turn off and the led
will
turn on
front, make sure that the hearing aid is between 15 and 25 cm away from the monitor to ensure
maximum audio quality during communication with the door panel.
.
- Co
mmunication
will last for 90 seconds or until
is
pressed. When communication ends,
door panel
vocal synthesis is enabled, a 'Communication is finished' message will indicate that the call is over.
.
-
To open door
or
of the door panel
, press the
2
1
screen
during the call or communication processes: one press will activate the lock release for
seconds and
door panel
LED
will also turn on for seconds. If vocal synthesis is enabled, a 'Door
open' message will be indicated on the door panel.
.
-
Detailed operation
and configuration
of the monitor
( )
INSTALA
TION OF THE
MONITOR
*
( )
For more information, see "AWD289" user manual
*
http://interco.ms/awd289
authorised personnel
.
.
dc
(1 to 128)
and
end of line.
displayed on the screen will blink green. To view the
LED
will turn off and the system will become free.
off-the-hook icon
sh wn on
o
the screen. Door
. If the monitor is a
n 'ART 4H LITE'
with icon
the button below
on-the-hook icon
shown on the screen
LED
will turn off and the system will become free. If
button below the
corresponding icon
displayed
3
, see "TART /G2+" user manual
4
.
ART4LITE/G2 MONITOR
2
DESCRIP
TION
( )
*
A
.
B
C
J
H
I
J
( )
*
Monitor address (code) setup:
Dip1 Dip7:
-
Sets the monitor address (addresses to
The switches set to OFF have a zero value. The values of the switches set to ON are shown in the table below. The
monitor code is the sum of the values of the switches set to ON.
Important: Apartment 1 (Dip1 to ON & Dip2-Dip to OFF).
Important: Apartment 2 (Dip1 - Dip to OFF).
Dip8: This activates the end-of-line resistance in the ON position. Activate it in monitors where the bus cable ends.
Deactivate it only in intermediate monitors.
Dip 8 a ON
. If the
ON
1
2
3
4
5
on the
Not : e To define whether the monitor is master or slave, entering the corresponding "Special code":
"0550" Master (factory default),
on the
3
is
MONITOR
A. Speaker.
B. Function buttons, access and selection of menu functions.
The function of each button is shown on the monitor screen with an
icon located just above each button (see "AWD289" manual).
Press to access 'Doctor mode' function (standby monitor):
D
*
-
With the special code '0441' (Doctor mode) already entered (see
special codes in manual "AWD289"), press the button
for 1 sec. to activate/ deactivate the function.
-
The push button led
E
function 'Doctor mode' is activated and it will turn off if the
function is deactivated.
F
C. Monitor status LED:
Yellow ON: Standby without notification.
G
Red ON: "Do not disturb" Mode activated.
D. 4.3" TFT color screen.
E. Alpha use only.
J
F. Microphone.
G. Raised dots for the visually impaired people.
In call
/communication
SA
GND
HZ
Above this raised dot is the 'Start/ nd communication' button.
HZ
BUS
Above these raised dots is the 'Door opening' button.
BUS
MADE IN CHINA
128
codes
SA
DIP 1 to 7
H. Configuration switches.
Monitor
GND
address
HZ
I. Installation terminals.
DIP 8
HZ
EOL
J. Wall mounting connector fixing (x4).
resistor
BUS
OFF = 0
ON = 1
BUS
J
Building / Villa (Nexa Door Panel)
1
1 8
2
).
Table of values
7
Switch number:
1 8
7
Value when ON
:1 2 4 8 16 32 64
Dip 8 a OFF
ON
6
7
8
1
2
3
4
5
6
7
8
"0551" Slave
1,
"0552" Slave or "0553" Slave .
2
3
will blink in white color if the
:
E
ON
1 2 3 4 5
6
7
1
2
3
4
5
6
7
8
Example: 0+ 0+4+0+ 16+
0+0
= 20
3