Alpha Communications TekTone NC505ES Installations- und Betriebsanleitung - Seite 5

Blättern Sie online oder laden Sie pdf Installations- und Betriebsanleitung für Empfänger Alpha Communications TekTone NC505ES herunter. Alpha Communications TekTone NC505ES 6 Seiten. Remote lcd receiver

Seite drucken

Alpha Communications TekTone NC505ES Installations- und Betriebsanleitung

Change Password

Passwords can be up to eight digits long. The default password

is 3446. To change the password:

1. From the Install & Service menu, press the

the CHANGE PASSWORD prompt.

2. Use the

and

buttons to scroll through the digits;

DOWN

press the

button to select and advance to the next

ENTER

digit. To select a space, press the

selecting a digit.

3. When finished, press the

the setting.

4. When PASSWORD CHANGED displays, press the

button to return to the menu.

DOWN

Monitor Signal Strength

The Signal Strength option is used to measure signal strength

and troubleshoot installation problems.

1. At the SIGNAL STRENGTH prompt, press the

POINT 01 is displayed, along with a signal quality of GOOD,

WEAK or NO SIG.

2. Use the

and

buttons to scroll through the registered

DOWN

transmitters.

3. Press the

button again to view level (LV) and margin

ENTER

(MA). LV indicates the overall signal strength; MA indi-

cates the signal strength minus the background noise.

4. To reset signal data, use the

and return to the transmitter you are monitoring.

5. Press the

button to return to the menu.

BACK

Figure 5—NC505ES Programming Menu Tree

READY

Press ENTER and

use arrow keys to

toggle thru selections

button at

ENTER

button without

ENTER

button again to complete

ENTER

button.

ENTER

and

buttons to leave

DOWN

INSTALL & SERVICE

EVENT LOG

POINT STATUS

Caution: When programming points, be careful not to map

faults to the same output as alarms.

1. From the Install & Service menu, press the

the SETUP POINT prompt.

2. Use the

press the

REGISTRD displays if a transmitter is currently registered to

this point; TX NOT REGSTRD displays if no transmitter is

registered to this point.

3. Press the

eight setup options are available:

Supervision Time—Sets time limit on reporting of missing

transmitters. Caution: Turning off supervision is not

recommended. The valid range is 0 to 99 hours. The

default is 60 minutes. Selecting 0 turns off supervision.

•

Use the

sion time.

•

Use the

(hours) and Min (minutes); press the

select.

Inactive Out—Maps transmitter/repeater inactivity fault output.

•

Use the

numbers. Choose - - to disable inactivity reporting.

•

Press the

this transmitter/repeater's inactivity transmission.

Tamper Out—Maps transmitter/repeater tamper fault output.

•

Use the

output numbers. Choose - - to disable tamper output.

•

Press the

this transmitter/repeater's tamper transmission.

PASSWORD

(Default is 3446)

Press Enter and

use arrow keys to

toggle thru results

Press Enter and

use arrow keys to

toggle thru results

IL882 NC050ES Remote LCD Receiver Manual • Page 5

Set up Transmitter Points 1–16

and

buttons to scroll through the points;

DOWN

button to select the point to be set up. TX

ENTER

button to set up the point. The following

ENTER

and

buttons to adjust the supervi-

DOWN

and

buttons to toggle between Hrs

DOWN

and

buttons to scroll through the output

DOWN

button to select the output to use for

ENTER

and

buttons to scroll through the

DOWN

button to select the output to use for

ENTER

PROGRAM OUTPUT

CHANGE PASSWORD

SIGNAL STRENGTH

DELETE POINT

SETUP POINT

Press arrow keys to

toggle thru selections

IL882 NC505ES MENU TREE REV 1 021710

button at

ENTER

button to

ENTER